Jump to content
SAU Community

Series 2 R34 steering wheel.

Wight

By Wight,
in Exterior & Interior Styling

 Share

Recommended Posts

Wight Apprentice

Wight

Posted
Posted

Series 2 R34 steering wheel.

Hi all,

Recently picked up a black series 2 R34, and it came with a steering wheel which didn't have the two tone trim (see image).

The other thing I noticed it doesn't have, is any stitching along the inside of the wheel. Is it possible the two tone trim has just been removed or has this wheel come from elsewhere (and the series 2 airbag module has been kept)?

The gaps between the airbag module are uneven, so my assumption was it had been swapped, but interested to see what others think.

 

DSC_0817.JPG

Link to comment
https://www.sau.com.au/forums/topic/468746-series-2-r34-steering-wheel/
Share on other sites
  • 1 year later...
sergi_dee Collaborator

sergi_dee

Posted
Posted

It's a series 2 wheel as for the emblem in the middle. Series 1 wheels only have the Nissan emblem embodied in the airbag. I want that wheel too! Haha

 

 

You also have the series 2 cluster. The gear and stereo surround is that golden colour which comes in the series 2's.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      ugently need expert / experienced opinion

      By GTSBoy 路 Posted

      There's more than one way to skin that cat, and most of the sump Maatouks have done will be GTR sumps. They are HUGE in GTR drag racing here.
    • dbm7
      Shifting questions

      By dbm7 路 Posted

      Yeah...I always start at the shift solenoids, because there's only a few reasons these will spook into limp mode, and bad shift solenoids is one ~ the other can be the shift control module (if you have steering wheel shift buttons)...it's easier to eliminate the solenoids first.
    • cabramatta
      Never ending fuel pump drama

      By cabramatta 路 Posted

      Might piggy back off this thread since there's been a good discussion about PWM.   I purchased a Walbro 460 F90000267 and have been looking into PWM to understand it. It was purchased more of a future proof as my original OEM fuel pump died (r33 below 200kw) and figured I'd just upgrade it to this. That's when it hit me that a pump this big can cause more dramas with such high amperage draw and heating of the fuel pump being on 100% all the time in such a mild setup.   I have a Nexus R3 and slowly collecting power mods but I was looking into the PWM feature on the NSP software:   Then looking at the graph from the fuel pump:     Am I safe to assume reducing duty cycle to 50% for example would make the pump run like a 230/lph ? Where does the PWM come in all of this ?   I've gone down the rabbit hole of PWM fuel pumps and it seems there are many differing opinions on how to go about it 馃槄  
    • DRoc81
      Shifting questions

      By DRoc81 路 Posted

      Thank you, this will keep me busy for a bit.  I will update progression.
    • sunsetR33
      ugently need expert / experienced opinion

      By sunsetR33 路 Posted

      That specific one would be an exchange part, meaning I'd have to send mine to them. Plus it looks like a non AWD sump, which won't work for me. There is one or two shops in my country that I can ask to do a sump extension job and it'd most likely end up being cheaper than sending mine to AUS or NZ and getting one back, and quicker too.
脳
脳
  • Create New...