Jump to content
SAU Community

New N1 block oil pressure location on block?

GD51LA

By GD51LA,
in General Maintenance

 Share

Recommended Posts

GD51LA Mentor

GD51LA

Posted
Posted

looking from under the car I can see the whole but I can't see any thread, maybe I need to look closer (possible?)

can i screw an oil pressure sensor straight into their?

does the N1 block normally come without a plug for that whole?

the new block is black in colour, and that hole is silver. a thread should be there correct?

Duncan Grand Master

Duncan

Posted
Posted

can you take a pic or describe better where you mean on the block? there is no location to screw a pressure sender to the block, in the standard setup it screws in to the oil/water cooler oil filter mount.

there is an oil feed on the passenger side rear but it is generally a turbo oil feed and would be the wrong size for a pressure sender anyway

Duncan Grand Master

Duncan

Posted
Posted

well blow me down. there is a plugged hole on my spare block just above and to the rear of the oil filter block mount on the driver's side. And it looks like the right size for an oil pressure sender although I wasn't able to check

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Zabuza
      Need AC Compressor for R32

      By Zabuza · Posted

      I’m thinking that’s the route I’ll  go, thanks for the input!
    • carnoobb
      V35 Overheat + Coolant Boil & Overflow + Engine not Starting

      By carnoobb · Posted

      Hey all, my 2004 Nissan Skyline 350GT overheated the other day with coolant boiling and leaking out of the coolant reservoir when I was parking. So today, I started it up again just to see if it was a thermostat/head gasket issue. After about 20 mins of running, temps were normal again, no coolant was leaking out and the upper reservoir hose was warm but my engine suddenly cut off. I checked the oil dipstick and cap when it was running and there was no white foamy residue and the exhaust did not have white smoke. I tried starting up the car again but it would only crank, similar to when I had a camshaft sensor issue just that now there’s no check engine light on the dash. Any ideas? Unfortunately I don’t have an OBD2 that can read the Nissan's programme.
    • Papichulo96
      Rb head oil drain dimensions

      By Papichulo96 · Posted

      Bump on this to not make another post, had a ‘head drain’ leak on me and have the engine out as we speak. Planning on just putting a new freeze plug back in , plug the tapped holes and just be done with that headache.    Now I still want to relieve pressure to allow oil to pass down the blocks returns easier. I’ve seen catch cans with multiple vents help folks with this issue on this forum.  I’m wanting to make my own. I have some pictures here of my setup if anyone can help how I should plumb and design the catch can I would deeply appreciate it !   rb25 Oil upgrades: 1.0mm restrictor n1 pump/billet gears extended crank collar  extended sump with trap doors/w welded fitting    
    • GTSBoy
      Need AC Compressor for R32

      By GTSBoy · Posted

      The Frenchy's kit is the way to go forward. A modern compressor that weighs about 1/2 as much, is at least twice as efficient, and will do a good job on R134a. And of course the kit has everything else you need to connect it up and have it work properly.
    • Zabuza
      Need AC Compressor for R32

      By Zabuza · Posted

      Hey all , I am in the process of having the AC system in my r32 GTST converted from r12 to r134a and I’m being told my compressor has gone bad and I will need a new one. I was wondering if anybody has any suggestions for what is the best route to go aside from dropping $1500 on a new oem one? I did see that Frenchy’s performance garage offers a kit to mount a Toyota compressor, has anybody actually used this kit on their car? Or is there anywhere I could purchase just a clutch? Any help is appreciated.
×
×
  • Create New...