Jump to content
SAU Community

Recommended Posts

Issue with alternator/headlights

So my r32 gtst is having this problem where my car batteries would die the next day so i changed the car batteries 3 times and the problem persist. I figured maybe it was my alternator so i got a multi-meter and tested it the numbers coming in were in the normal ranges. I tried all the load test and they came back normal but the one thing i noticed was when i had my headlights on and i revved the car the voltages would drop on the meter down to not so normal ranges around 12 volts. On idle everything is normal but when i rev up the car around 1500-2000 it goes down only when headlights are on any idea what could be the problem?

Link to comment
https://www.sau.com.au/forums/topic/469387-issue-with-alternatorheadlights/
Share on other sites

Why say "I got normal numbers"? wouldnt it make more sense to give actual voltage readings? not trying to be rude but perhaps they are not normal numbers.

It sounds like the altenator is not able to keep up with high load, so above statement is possibly correct. More info needed

flux capacitor needs replacing...lol

Take the alternator out and get it checked by an auto sparkie shop....they have the best test rigs for this and generally they will test for nothing or at worst nominal cost.

Sorry i assumed people would know what normal voltage readings is if they knew about what i was talking about lol. The voltage reading is around 13.90v-14.30v on idle no load with load 14.11v - 1370v with headlights on only it idles about the same but when revving the engine it drops too around 12.38v. Probably is the alternator thanks for the quick response.

On 04/03/2017 at 7:33 PM, Robzilla32 said:


This - you haven't installed an amp recently? Probably obvious but I did this recently and the battery was draining super quick.

I was actually trying to diagnose issues with HICAS, upping the earth strap definitely helped. But yes I have an amp (two actually haha).

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • What can't be done with a little bit of decking board or similar timber bolted to a hub flange via 2 wheel nuts is not worth talking about.
    • I noticed something. On the tps sensor and the sensor behind the adjustment screw is adjusted towards the far left. Are these screws supposed to be centered? (this sensor was in the same position before the tune as well)  Also attached a photo of where my car usually idles at when warm (sometimes a tiny bit above that). I think I might have screwed up the calculation and it might have better than I thought lol at 750rpm still not 650rpm though.      
    • So for both general interest of engine health, and to rule out any coolant/oil issues, I organised an oil analysis done on the 125,000klm oil Results below, all good, just a bit of fuel dilution which I'm not too worried about
    • This is actually a really good way of measuring what wheels fit. If only there was a similar measurement between hub face and suspension :p That said, it's probably pretty simple to actually measure it all with the wheel off the car for the rear. The front is a bit more complex but.. 
    • Being the top Google search result for R34 wheel-related inquiries, lemme throw down my experience. I calculated that 100mm from hub face to wheel face is about the perfect fitment for my ENR34 sedan.  I've been running 18x8.5s, ET35, with a 1" spacer. So, 8.5in to mm = 216mm. 216/2 = 108mm. 108-35 = 73mm. 73+ 25 (1" to mm) = 98mm.  If you wanna get close to this on dif widths, here are the offsets you'll want: 9" - ET around 15mm 9.5" - ET around 20mm 10" - you're crazy, but ET around 30mm All these should fit perfectly on a non-widebody, non-GTR Skyline. Note that it's probably the absolute max, and you're probably better off running a couple degrees of camber in this config, but it looks great, super flush.
×
×
  • Create New...