Jump to content
SAU Community

Gearbox oil leaking into transfer case

stealthfoz
 Share

Recommended Posts

  • 2 weeks later...
rockvale Rookie

rockvale

Posted
Posted

Ok lets try and help the guy, it does not matter how you fill the transfer case  or gearbox as long as the correct type and amount of oil is used, un qualified comments by idiots dont bother putting your comments up.

now to your issue of gearbox oil transferring to the transfer case via your centre plate?? (hoping this is what is happening)

1. Can occur if transfer case pump main shaft seal is worn, damaged, or not installed

2. Seal on Shifter Rod worn, damaged, or not installed,

3. But this issue of transfer of gearbox oil to transfer case oil is generally cause by a broken magnet on the transfer case drain plug (Eg the magnet is entirely missing from the transfer case drain plug) What happens over time is the metallic compounds do not collect on the transfer case drain plug magnet (because it is missing), instead the metallic compounds block the very fine filter of the transfer case oil pump filter which creates a high suction vacuum substantial enough to suck gearbox oil past the transfer case pump main shaft seal. The result becomes evident when the transfer case fills up with the mixed oil and overflows out the transfer case plastic breather hose and onto the hot exhaust causing smoke. If your magnet is not present on your transfer case drain plug, you will need to remove and wash clean the  transfer case pump filter and replace

1. The transfer case pump main shaft seal

2. Replace the transfer case drain plug (one with magnet in good condition)

Yes, I have done this twice for customers R32 GTR'S, sorry, but not a small job for such a small damaged magnet on a drain plug!!!       

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Rb26/30 build

      By MBS206 · Posted

      And if you want more power, more reliably, and cheaper, go get the Aussie RB... The 4L Barra and put that in instead.
    • MBS206
      Nismo rear spats

      By MBS206 · Posted

      No cats will keep discolouring the rear bar. Sends white paint a weird yellow stain. Cut and polish normally gets it out, but you'll be doing that every fortnight I found.
    • Butters
      Rb26/30 build

      By Butters · Posted

      Both heads will be equally reliable or unreliable depending on what you do to them.  Stock the RB26 head will flow more. You have access to the stock intake ITB manifold on the RB26 cheaply which flows really well(1000hp+).   Arguably more aftermarket support for RB26, though in Aus we love our RB30 SOHC heads too.    The only downsides to the RB26 head is if you have a VL commodore and want to keep the SOHC look.  Where you may have an issue is drilling out the rb30 block for the bigger head studs but if you are building a big power motor you'd probably put bigger studs on the SOHC head too.  This is just about finding a good machine shop, sometimes easier said than done.  RB30 head worked can make big power just like a Rb26 head, so really it actually more comes down to what your preference is for your car.  People now even making billet versions of both.
    • GTSBoy
      Rb26/30 build

      By GTSBoy · Posted

      2630s work perfectly well. There is something to be said for just using the 30 head, as it saves all the pain of the conversion, still makes tons of power, still sounds cool, etc etc. 2630 will obviously make more power again, but the differences are not stupidly big. It really depends on whether you're racing for sheep stations or not. If it's dead serious, then it's a 26 head. If it's just for fun, it could go either way. But the 26 head and the effort to get it set up, etc etc, is part of the fun.
    • lilley's gtr
      Rb26/30 build

      By lilley's gtr · Posted

      I've been building a 26/30 for a few years now. I've had the head built with all the good stuff. I had a 32 gtr but blew it up and yes its all going into a vl but im looking for some advice from some RB nuts on pros and cons on putting a 26 head on a 30 bottom end is it worth it Works are as follows Head -Extensive porting 1mm oversized supertech valves Supertech double springs Supertech valve guides Supertech titanium retainers Tomei solid lifters Tomei 270 x 10.25 cams Head drain Bottom end series 2 rb30 block Cp ceramic coated pistons Eagle rods Romac balancer Oil restrictions  O ringed blah blah spent a fortune And will get a girdle because the 30s arent used to handling that much rpm Nitto billet oil pump Hypertune plenum 6boost mani Refurbed astra pump thats the cover for it in the boot I did have a precision 6262 but sold it because drag car life. Currently building the ass end full 4 link floater rear end with a 2 speed  But the dilemma i have is my mate rekens I should just stick with the 30 head for reliability. Has any one had any issues with mounting the 26 head ie compression blowing gaskets etc. Just looking for some advice from people who have gone down this route. Here's some photos. Blew the oil pump in the gtr and decided to rip the motor out at the time and do a full build only to find it had been a repairable write off so went down this path.     
×
×
  • Create New...