Jump to content
SAU Community

Rb26 intermittent miss, runs a bit off. Sarted after driving in heavy rain.

GonzoGTR
 Share

Recommended Posts

GonzoGTR Apprentice

GonzoGTR

Posted
Posted
Rb26 intermittent miss, runs a bit off. Sarted after driving in heavy rain.

Hey everyone. Im a bit stumped and perplexed at this point. I have a 99 stagea 260rs. It has an apexi power fc, other wise stock engine.
Anyways i went with a friend to go look at a cheap Delica an hour away on the weekend, on the drive back it was a nasty downpour. I noticed when i took over driving the engine sounded a bit off at idle when i stopped to switch seats with my friend. Got home and when holding the revs at 2-3k rpms a noticeable intermittent miss occurs. At idle the car sounds off, almost more of a honda sound with a rice can,  same as revving under load it has a riced out honda sound (as funny as that sounds). This all happened after driving in really heavy rain for over an hour. 

It's also revving just  bit higher as well. I noticed the commander will say 900 rpms for current revs while the tach reads about 1050. It sounds like a bit faster idle as well

Only 2ks ago i put in new plugs ngk bcpr7eix, and put on super spark coil packs when i got the car. 

I was thinking a plugin or coil pack got wet. After the rain i have gone and pulled any plug i could find including the ignitor, and dryed with compressed air then applied dielectric grease to each plug as well. No difference. I pulled all the coilpacks and even pulled a plug. I bought new coppers to run, but after pulling the new irdium plugs i decide dto keep them in there as no evidence of  of foul plugs was present.  The plug looked in great shape and no coil packs or plugs were wet. I installed my old set of stock coilpacks and no difference either. I can hear a noticeable miss from each cylinder when i pull each coil pack plug as well so its not one individual/constant miss. 
I have a friend with a spare igniter that i am going to try as well. I'm not really sure what next to do.

I also checked the wiring but didnt seem to notice anything change while checking the ignition harness and plugins.
I was thinking fuel but i dont think so as im not getting a knock but it could be fuel im not sure. The fuel filter is fresh as well but i can change that too. 

When i was going through the apexi fc commander i noticed that the second O2 sensor is sending no voltage or 0.04V so im guessing that's gone. I don't know if that would cause the miss tho.
There is an aftermarket grounding kit that goes to the ignitor as well. I had to put on larger north american terminals and can't get the greatest contact but after adjusting he grounding kit there was no difference.
Any ideas would be appreciated. I'm a bit stumped and i was considering selling my stagea then this develops.
Thanks!

niZmO_Man Grand Master

niZmO_Man

Posted
Posted

From my experience, R32s are voltage sensitive, so make sure the battery terminals and grounds/earths are good.
Also, does it have standard AFMs? I'd re-solder the pins inside as they're old now.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • robbo_rb180
      Rob's S Chassis track cars. Now with more s15 and less 180sx

      By robbo_rb180 · Posted

      Also did some work to the shed and a massive clean out of stuff. It's now got a small fab/dirty room and has helped keep shed cleaner. Built some new work benches and re organised things also got a TV out there so good having something playing while working on the cars. Got a pedestal drill and linisher off a mate that need to pick up too.  
    • Murray_Calavera
      R32 GTS (RB20DE) Injectors Replacement

      By Murray_Calavera · Posted

      First thought, have your current injectors flow tested. If they test fine, keep the diagnostics going. It's not the injectors. If the injectors are the issue, find some new or used (cleaned and flow tested) injectors.  While I really love a good excuse to get a modern ECU installed, just needing new injectors probably isn't a good enough reason to do so. 
    • robbo_rb180
      Rob's S Chassis track cars. Now with more s15 and less 180sx

      By robbo_rb180 · Posted

      A bit from column A, B and C. Mainly C   Update time, after deciding it was time to tick off a bucket list goal I finished up full time at MSR and have gotten back behind the wheel and making progress on the S15. Goal has been to drive Bathurst at an event and I have had my entry accepted for Challenge Bathurst in November. Since I don't want to go unprepared I need it running to test and get comfortable.  Been chipping away at it and started by stripping inside, getting it all cleaned and sealing some holes up. With stripping inside I removed the whole wiring loom and found a few surprises.......... its pretty butchered and shit branching and I'm not a fan of the haltech fuse boxes so it's all out and trying to come up with a plan to rewire it all either new fuse/relay box or pdm.  I haven't been happy with how I did the intercooler mounting and been wanting to tuck it up under rad support. O e issue with that is headlights will need a decent trim or get replacement covers. Took the time to mount it with some stand off's and new hardware. Stands are some m8 button bolts, washer, aluminium tube and factory radiator top mount rubbers. It's nice and solid also stiffens rad support which still requires some trimming. Bonus of factory rad mounting is used all factory hoses just need to weld a pressure cap to radiator now. Got sensor block and fuel filter mounted. Plan today is to get vac lines all sorted with push in nylon tube and design oil cooler mounting solution.  Been driving BRZ a heap and went out to Morgan Park for time attack and went pretty well for a wet day. https://youtu.be/gAlQgcQpWj4?si=kojOAOjhhX_X3AXR Getting pretty comfortable in it now and want to do a few more bits to it but restraining myself as don't need 2 race cars at the moment.   
    • Murray_Calavera
      Anyone know this frontpipe?

      By Murray_Calavera · Posted

      @sunsetR33 There is obviously a huge culture gap here. There is nothing in place like this in Australia, where if you fit a Mines branded pipe and later replace it with a Jun branded pipe, both pipes are essentially identical - BAM - huge penalties! Where is the Mines pipe?? You can't have a Jun pipe when you said you had a Mines pipe!  Makes no sense to me. Surely makes no sense to anyone else here either.  I'm sure a lot of us would agree that our registration/engineering system is pretty stupid at times, but it's not that stupid.  *** More serious question here. If you replace a factory rubber hose with a silicone hose, is the car illegally on the road now? Does it become legal if you have certification of what brand the silicone hose is? Then would it become illegal again if you replaced that silicone hose with a difference brand of silicone hose? And then would it become legal again if you had certification of the new brand of silicone hose?  I really want to know that answer to that question. 
    • robbo_rb180
      The Ls1 R33 Of Fury

      By robbo_rb180 · Posted

      Good you making progress with this rig. Aluminium welding is painful to learn, have you got a pedal as I found it so much easier with one. If that's the AMG I think it is, you would working with Benny?
×
×
  • Create New...