Jump to content
SAU Community

Does S3 front lip fit on an S1 R33 GTR?

CSNet

By CSNet,
in Exterior & Interior Styling

 Share

Recommended Posts

CSNet Collaborator

CSNet

Posted
Posted
Does S3 front lip fit on an S1 R33 GTR?

Hey guys,

 

As mentioned in the thread title, does anyone happen to know if the s3 (or even an s2) front lip (the black thing under the front bar) fits straight onto an S1?

 

I know the lip is a bit bigger, but I assume it all lines up to bolt straight on? Any help much appreciated

 

Cheers

Link to comment
Share on other sites
GTR-N1 Grand Master

GTR-N1

Posted
Posted

I've had no problem,...

Trajkovski-1_zps2x0epbx0.jpg

 

But the N1 Kevlar Undertray required a fabricated spacer strip so it could be attached to the lip.

Terry-35_zpsowlkupd5.jpg

 

All the best. :)

 

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • RB25inside
      Compatible rear drive shafts R34 N/A?

      By RB25inside · Posted

      Are these the Dmax ones you are in reference too? https://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35#description Not a bad idea to get the uni flange ones. I have sent just jap an email too. Will see what they say lmao. Only thing is the Dmax ones are on a big back order. Low key anything will be better then my OEM ones I got as they are sounding like popcorn when I go under load lmao 😂☠️🪦.
    • GTSBoy
      Compatible rear drive shafts R34 N/A?

      By GTSBoy · Posted

      They should do. I have S14 (or something S chassis, anyway) driveshafts in my R32 (because my diff flanges have 3x2). They're the right length. When you go looking for R32/3/4 driveshafts (for turbos), they're all the same thing, so are the same length. So there really shouldn't be any reason why those cheapies from JJ won't also fit an R34. R32/3 NA should also be the same thing. The (3x the price) D-Max ones are uni-fit. They have 5x1 and 3x2 bolt holes and say they cover all the cars. So that would also suggest that they are all the same except for the flanges. And in that case, the flange goes both ways. I'd be buying the D-Max ones if I ever have to replace a shaft. Because that will open up diff options without needing to juggle shafts also. Juggling shafts is gay.
    • ChoppedSpots
      GReddy Injector Help!

      By ChoppedSpots · Posted

      Yeah with the adaptors they do look like the photo above - just the fitment within the plenum itself and then further with the rail to the intake is questionable - we shall see tomorrow hopefully once I get some replies from Aeroflow, maybe those bosses are the missing piece....
    • Dose Pipe Sutututu
      GReddy Injector Help!

      By Dose Pipe Sutututu · Posted

      Should be fine, if you have it sitting too far in, you end up just spraying the walls and have shit idle. You "can" run them like that, however I don't think it's a great idea (also depends on your plenum, might be good to just get the injector bosses first, mock it up and see if you need to get the bottom extension) Ideally your injectors, with the extension should look like this  (Not my photos, just Google)
    • ChoppedSpots
      GReddy Injector Help!

      By ChoppedSpots · Posted

      Thanks for the replies guys, it's really appreciated.  It seems the kit was supposed to come with those injector bosses but hasn't. Unsure if they'll help as even with the adaptors to make them a 3/4 height injector they still sit too far out so mount the fuel rail?
×
×
  • Create New...