Jump to content
SAU Community

Recommended Posts

R34 gtr cold side r32/33 hotside r34 Gtr cam covers Rb26 head r34 bottom end

Complete r32/33 Gtr hot side,airflow meters ,turbos have little play 70k done 

$440

complete cold side with injectors

$490

 

r34 Gtr cam covers comes with breathers hoses ,coil wiring loom, 34 cam sensor ( note the spark plug cover has cracked at the rear of the head, just need to be weld back together )

$890

 

rb26 cylinder head, has been surfaced and crack tested. Also has had 4 hrs spent cleaning up the ports. Comes with the r34 Gtr cams. Currently disassembled.

$1100

r34 complete Rb26 block with 80k 

Bores look ok. Was a running motor.comes with oil cooler engine mounts sensors alternator harmonic balancer 

$2400

 

IMG_7276.JPG

IMG_7291.JPG

IMG_7292.JPG

IMG_7294.JPG

IMG_7309.JPG

IMG_7319.JPG

IMG_7330.JPG

IMG_7709.JPG

IMG_7940.PNG

IMG_7942.PNG

Victoria,

 

i also have a set of rb26

r32/33 steel wheel turbos. I was told they were reco 15k ago.

little shaft play.

$350

amd a 300kph early r32 Gtr speedo cluster. 120k on dash

$240

  • 5 months later...
  • 1 month later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Is there a diameter difference in the stock to Nismo? If so, the weight alone won't be indicative when comparing flywheels of the same diameter, since the radius of the flywheel acts on the moment of inertia with a square factor, where as mass is linear. Roughly going from a 4.5kg flywheel with radius 20cm, to a 9kg flywheel with radius 14cm would see them act the same. This calc is just here to act as a brief numbers comparison and reflects no actual RB flywheel diameters etc. it also assumes even weight distribution (thickness) throughout.
    • It seems this could be due to a restructure/team direction change... Or... You're working with a different category of vehicle... Or you've decided you'd rather be able to play with your own cars again...   I'm hoping the latter...
    • had 4 weeks off over xmas and well did some stuff to the shed and BRZ, well short of is I don't work full time in supercars anymore as of yesterday.........
    • Did you get any down time over Christmas, or have you had any since to play with this? Or have you given up and are trying to get yourself a second hand V8SC instead?
    • A random thought I had just before I hit "Submit on this post". If brake fluid, in a container in my garage that has never been opened goes bad after 18 months, why can I leave it in my car for 24 months in an "unsealed container"... Secondly, some other digging, and brake fluid manufacturers seem to be saying 5 year shelf life... Me thinks there line on 18 months for an unsealed bottle is pretty much horse shit marketing spin. Kind of like how if you drive a car and don't run a turbo timer your turbo and motor will die horribly...   Where I started on this though... Someone (me) started down a bit of a rabbit hole, I don't quite have the proper equipment to do Equilibrium Reflux boiling per the proper test standards. I did a little digging on YouTube, and this was the first video I found on someone attempting to "just boil it". This video isn't overly scientific, as we don't have a known reference for his test either. Inaccuracy in his equipment could have him reaching the 460 to 470f boiling point range in reality. In the video, using a laser temp gun, he claims his Dot3 that's been open in his florida garage for over a year gets to about 420 to 430 fahrenheit (215 to 221c) Doing some googling, I located an MSDS for that specific oil, and from new, it claims a dry boiling point of 460 to 470f. Unfortunately they don't list a wet boiling point for us to see how far it degraded toward its "wet" point. While watching it I was thinking "I wonder what the flash point is..." turns out its only 480f for that specific brake fluid....   As for testing the oil's resistance, I might not be able to accurately do that unfortunately. Resistance level will be quite a LOT higher than my system can read I suspect based on some research. However, I might be able to do it by measuring the current when I apply a specific voltage. I won't have an actual water % value, but I'll have some values I can compare between the multitude of fluids. I'll run some vague calculations later and see if I should be able to read any reliable amount of current. These calcs will be based on some values I've found for other oils, and see how close I'll need my terminals together. From memory I can get down to 1pA accuracy on the DMM. I don't think my IOT Power Tester has any better resolution.    
×
×
  • Create New...