Jump to content
SAU Community

Recommended Posts

Skyline R34 engine light

Hey everyone,

Recently on my skyline r34 non turbo 4 door my engine light as come on twice within a 1 week period and am unsure of its cause.

First the car is fine and then the engine light comes on (this is happened twice), no problems occur untill I stop at a set of lights and it starts to jitter back n four over 6 beats (this has only happened twice and I've stopped many other times with no jitters). I pull over and turn the engine off and wait a couple of seconds and then turn it back on and the engine light is gone. 

I believe it is just a ecu problem but I wanted to ask if anyone else had experienced this and how to fix it? 

Thank you for your time.

 

Link to comment
https://www.sau.com.au/forums/topic/471183-skyline-r34-engine-light/
Share on other sites

You can run a auto diagnostic on it via the consult port. You just need a paper clip. There's a write up somewhere on here that will tell you how to do it. Other option is to get a consult device to read the codes.

Quick little update; 

The car only seems to display the engine light 3 minutes ish after driving, after I turn the engine off and on it goes away for the rest of the trip (drive for an hour or so). 

It only seems to appear when the engine is cold.

Will be running a diagnostic in a couple of days to see whats happening. 

Thanks for your advice it will definitely come in handy :)

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • They see me rollin' they hatin'....... Took me most of the day to make the necessary mods to the mounts to make them fit the car.  Fortunately I was able to just use the mounts that came with the rotisserie. The rear ones are really secure, the front I feel i might reinforce a bit more as it doesn't seem like enough attachment to the vehicle. I'm sure it's fine but better to be safe than (extremely...) sorry.  I drilled and tapped thread into additional M12 holes to each car mount where it attaches to the rotisserie as an extra fail-safe. Without them the side to side movement is just restricted by the allen head pinch bolts, nothing actually goes though the beam. Does now! I still need to adjust the rotisserie to get the car centred in terms of centre of gravity. If it's too high or too low relative to the rotational centre line of the car, it will be like a turtle and roll onto its back or as it currently sits, I dont think I'd be able to rotate it as it sits as it needs to lift the whole car up as it rotates. Ain't happening... I'm going to be nervous as hell the first time I go to spin it on its side...    
    • Oh yes done this when the window started flopping around.  Turns out the guides that run along the rail chanel had crumbed way. Took off the door card and pulled out the window mech, then the window, which you have to pull out through the top. As said unbolt the guide rail and don't spend 30 minutes getting frustrated trying to find a way to slide it out upwards cause that don't frigging work. Drop it down and out through the door hole. All I did to repair it was slice some 10mm clear plastic tube, vertically, then screw it to the guide rail both sides. This tubing rolls inward on both sides and leaves a gap wide enough to hold the window. To finish all I did was lube the plastic tube with olive oil and Bob's your uncle . . . well if he has the operation he can be your Aunt ! !  10 bucks in plastic tube and another 5 minute job done again . . . . YEH BULLSH#T ! My love for Skylines knows no bounds !
    • So was there a solution to this problem? I’m having this issue now. 
    • not expensive, just irreplaceable if you don't go sub 60 at wakie in that thing people will start talking
    • I haven't replaced that, but I have had the doors apart on the r32 a couple of times The door skin will be held on by a combination of clips and bolts, just take it slowly and make sure all the sneaky hidden bolts are out Once the skin is off you should be able to pop that piece off pretty easily, looks like there are only 2 bolts holding it on
×
×
  • Create New...