Sack87 Posted February 22, 2019 Author Share Posted February 22, 2019 Didn't happen today, battery is f**ked so need another one. Looks like next weekends job now. Link to comment https://www.sau.com.au/forums/topic/471232-brendons-m35-build/page/5/#findComment-7898972 Share on other sites More sharing options...
andynogo Posted February 22, 2019 Share Posted February 22, 2019 Dude! Come on! Get a battery already! We're all waiting!! 1 Link to comment https://www.sau.com.au/forums/topic/471232-brendons-m35-build/page/5/#findComment-7898974 Share on other sites More sharing options...
Sack87 Posted February 22, 2019 Author Share Posted February 22, 2019 4 hours ago, andynogo said: Dude! Come on! Get a battery already! We're all waiting!! Haha, not payday until Wednesday and the power steering is leaking from a dodgy fitting. Link to comment https://www.sau.com.au/forums/topic/471232-brendons-m35-build/page/5/#findComment-7898987 Share on other sites More sharing options...
Sack87 Posted March 1, 2019 Author Share Posted March 1, 2019 Got the airbox mod 3d printed and temporarily screwed it on as it's only minimum infill for trial. Fits perfectly and the cold air inlet sits just outside the main frame rail. Also modified the power steering reservoir by making my own bracket as it didn't clear the bonnet when closed in the stock one. 2 Link to comment https://www.sau.com.au/forums/topic/471232-brendons-m35-build/page/5/#findComment-7899514 Share on other sites More sharing options...
Sack87 Posted March 2, 2019 Author Share Posted March 2, 2019 (edited) So I got it going today but have a few issues. Turbo coolant hose has split, kinda knew it would. Power steering keeps leaking at the pump so just going to use the old setup Crank position sensor is throwing a code so it could be f**ked It keeps overheating. Doesn't matter what I do, i can't get it to not overheat. Edited March 2, 2019 by Sack87 Link to comment https://www.sau.com.au/forums/topic/471232-brendons-m35-build/page/5/#findComment-7899552 Share on other sites More sharing options...
Sack87 Posted March 2, 2019 Author Share Posted March 2, 2019 VID_20190302_113249.mp4 1 Link to comment https://www.sau.com.au/forums/topic/471232-brendons-m35-build/page/5/#findComment-7899555 Share on other sites More sharing options...
TukeH Posted March 2, 2019 Share Posted March 2, 2019 Whats that strange cliking sound is? Link to comment https://www.sau.com.au/forums/topic/471232-brendons-m35-build/page/5/#findComment-7899559 Share on other sites More sharing options...
Sack87 Posted March 2, 2019 Author Share Posted March 2, 2019 (edited) 1 hour ago, TukeH said: Whats that strange cliking sound is? When the water hits the power steering belt it makes that weird noise. You can see the water spitting out of the radiator neck. Took me a few minutes to figure out what it was haha Edited March 2, 2019 by Sack87 Link to comment https://www.sau.com.au/forums/topic/471232-brendons-m35-build/page/5/#findComment-7899565 Share on other sites More sharing options...
Akshunhiro Posted March 13, 2019 Share Posted March 13, 2019 Nice work with the airbox. Would you mind sharing the STL? Or, can I buy one off you? My 3D printer is still waiting to be assembled haha. Link to comment https://www.sau.com.au/forums/topic/471232-brendons-m35-build/page/5/#findComment-7900526 Share on other sites More sharing options...
Sack87 Posted March 13, 2019 Author Share Posted March 13, 2019 17 hours ago, Akshunhiro said: Nice work with the airbox. Would you mind sharing the STL? Or, can I buy one off you? My 3D printer is still waiting to be assembled haha. Let me test it out first to see how it goes with the heat, then I'll look at selling the STL file if it doesn't melt haha It only just fit on the Makerbot Replicator bed so yours needs to be the same size. Link to comment https://www.sau.com.au/forums/topic/471232-brendons-m35-build/page/5/#findComment-7900579 Share on other sites More sharing options...
Sack87 Posted March 15, 2019 Author Share Posted March 15, 2019 So I got the coolant bled to a point where I could drive it without overheating and run the engine in for 100km. Installed a GFB G Force 3 boost controller on a little bracket I made up that fits in the vent. I can monitor AFR later on when I put another sensor in and protect the engine incase it leans out. So many cool features with this unit. Also had a mate dip the grill in carbon fibre. Came out really good and matches nicely with the ARX kit. 4 Link to comment https://www.sau.com.au/forums/topic/471232-brendons-m35-build/page/5/#findComment-7900777 Share on other sites More sharing options...
Sack87 Posted April 3, 2019 Author Share Posted April 3, 2019 I haven't had much luck with the car as of late. Noticed there was engine oil coming out from the bell housing and whilst under there, I also noticed oil coming from the turbo between the cartridge and turbine housing. Pulled the box out haphazardly as I didn't have a hoist and pulled the turbo back off too. I cut the rear main seal by accident when installing it on the stand without being able to see the back of the crank. Turbo went back to MTQ for warranty and they reckon nothing was wrong but replaced the oil seals. Fitted new rear main which is an absolute f**k to get in there and box and turbo back in for test drive. I put new viscous oil in the fan hub last night and it works/sounds like it's moving a lot of air now. Went to go for a drive, look under the car for leaks after putting it all back in andddddddd oil is pissing out of the turbo feed banjo. FML. I checked every fitting was tight before I put it back in so MTQ have done something there. So today I started pulling the turbo back off again to fix that. Link to comment https://www.sau.com.au/forums/topic/471232-brendons-m35-build/page/5/#findComment-7902091 Share on other sites More sharing options...
Sack87 Posted April 4, 2019 Author Share Posted April 4, 2019 So MTQ decided it would be good to reuse the aluminium washers which are all f**ked up and not flat. Thanks dream boats Link to comment https://www.sau.com.au/forums/topic/471232-brendons-m35-build/page/5/#findComment-7902129 Share on other sites More sharing options...
andynogo Posted April 4, 2019 Share Posted April 4, 2019 Yeah... It's one thing after another hey. Keep on trucking- you'll get there! Half price boost night 17 April at whoop ass... Might be a few of us going... Link to comment https://www.sau.com.au/forums/topic/471232-brendons-m35-build/page/5/#findComment-7902133 Share on other sites More sharing options...
Sack87 Posted April 4, 2019 Author Share Posted April 4, 2019 20 minutes ago, andynogo said: Yeah... It's one thing after another hey. Keep on trucking- you'll get there! Half price boost night 17 April at whoop ass... Might be a few of us going... I would but i'll be on arvo shift. I plan too make it down there soon before seasons end. Link to comment https://www.sau.com.au/forums/topic/471232-brendons-m35-build/page/5/#findComment-7902136 Share on other sites More sharing options...
Sack87 Posted April 6, 2019 Author Share Posted April 6, 2019 So it's back in business, no leaks so much success. Hob drive still says its overheating though but the gauge does not move whether it's 75 or 105. The new fan oil helped a bit but I think it might be a faulty sensor. Link to comment https://www.sau.com.au/forums/topic/471232-brendons-m35-build/page/5/#findComment-7902251 Share on other sites More sharing options...
andynogo Posted April 6, 2019 Share Posted April 6, 2019 Have you tried a wired temp sensor temporarily shoved up a rad hose? Might confirm if it's getting hot or not... Link to comment https://www.sau.com.au/forums/topic/471232-brendons-m35-build/page/5/#findComment-7902273 Share on other sites More sharing options...
Sack87 Posted April 25, 2019 Author Share Posted April 25, 2019 Went to the drags last night, did a 14.4 and popped the motor. FML 1 Link to comment https://www.sau.com.au/forums/topic/471232-brendons-m35-build/page/5/#findComment-7903742 Share on other sites More sharing options...
Ben C34 Posted April 25, 2019 Share Posted April 25, 2019 Well that sucks,.... Head gasket or worse? Link to comment https://www.sau.com.au/forums/topic/471232-brendons-m35-build/page/5/#findComment-7903749 Share on other sites More sharing options...
andynogo Posted April 25, 2019 Share Posted April 25, 2019 Daymmmm! What the fark happened? I went last week and managed to coax a 14.3 out of my lardy ass Stag. Link to comment https://www.sau.com.au/forums/topic/471232-brendons-m35-build/page/5/#findComment-7903758 Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now