Jump to content
SAU Community

Recommended Posts

Haha which part mate? 
No sorcery just good gear and products [emoji4]

My Stagea looks in similar nick to that WRX with the spiderwebbing. I'd be most keen to learn how you get your results.
  • 2 months later...
So this little guy is a Flex PE-8 its an 800W rotary polisher. I f**ken love this little guy! 
I have backing plated from 3" down to 1" and with the extension bars that i have there literally isn't a place i can't get to [emoji4]
20170609_153629.thumb.jpg.03edd82e0ace457833ed76efc71fc0aa.jpg


He mick_o

How do you find this guy on the paint, being a rotary and all?
I've recently purchased a 3401 and love it.... but since the cars I have all seem to have little bits that I'll never be able to get the 3401 with a 5in pad I'm looking to get something smaller to use in conjunction with the 3401[emoji4]

Its an absolute must have mate. I dont run it any higher than on 2 even slower if you have a heavy cut pad.

Obviously being rotary they do create alot of heat quite quick so dont apply much pressure or stay stationary long.

Generally speaking an orange pad (light/medium cut) will be good enough to correct most defects with an appropriate cut compound for the correction needed. Least that way the softer pad wont generate the friction or heat that can burn paint and cause those "horror stories" you hear of people burning their paint ?

  • Like 1

Another tip would be play with different combinations of pads and compounds. Dont think you HAVE TO only use a heavy cut compound with a heavy cut pad. 

Play around a bit. Sometimes you might get the desired level of correction you need with a light cut pad but heavy cut compound for example. 

The aim of the game is to take the minimal amount of clear off needed to chop out those swirls and scratches ?

  • Like 1
3 hours ago, HKL32R said:

Hey mick, any tips for when using a clay bar i need to do my car but not sure how to go about it.

Hi mate only clay bar your car if you plan on giving it a full detail.

Its basically the 2nd step (after washing) As it will be stripping off any wax or sealants you have on your paint.

A clay bar is an abraisive so cuts all the surface decontamination away and those contaminants stick to the clay.. It leaves you with a fresh clean surface ready to start your correction/polishing process. ?

Hi mate only clay bar your car if you plan on giving it a full detail.
Its basically the 2nd step (after washing) As it will be stripping off any wax or sealants you have on your paint.
A clay bar is an abraisive so cuts all the surface decontamination away and those contaminants stick to the clay.. It leaves you with a fresh clean surface ready to start your correction/polishing process. [emoji4]
Thanks heaps yeh i might give a orbital polisher a go i been doing it by hand and it takes me all day and i still cant get it glass like your pictures. :D

Yeah you could never do the work of a polisher by hand haha! 

So for the clay bar process obviously make sure the car has been washed. Grab your bar and knead it into a size that covers your 4 fingers. 

For claying you need lubrication (spray detailer) to prevent marring and further adding swirls. 

Try working in 2ft squares. Add plenty of spray detailer and work in up, down left, right motions not circles. 

You will feel the clay kinda dragging. Can even sound like sandpaper sometimes on bad cars!

Basically work in the above actions till the clay bar slides smoothly over the surface. 

Use a microfibre cloth to wipe off the spray detailer and move to the next section. 

Check your clay bar after your section and see what crusty crap is on your bar. 

After every section you should knead up your bar again so you have a nice clean section to work with!

Heres a mad tip too...

After you wash your car run your fingertips over your paint.. You will feel how rough it is.. 

Go grab yourself a plastic sandwich bag or the likes put your hand in the bag and feel the paint again. 

Let me know what you feel ?

Do that before and after claying the car to know if you have got all the surface contaminants off ready to polish her up!

Yeah you could never do the work of a polisher by hand haha! 
So for the clay bar process obviously make sure the car has been washed. Grab your bar and knead it into a size that covers your 4 fingers. 
For claying you need lubrication (spray detailer) to prevent marring and further adding swirls. 
Try working in 2ft squares. Add plenty of spray detailer and work in up, down left, right motions not circles. 
You will feel the clay kinda dragging. Can even sound like sandpaper sometimes on bad cars!
Basically work in the above actions till the clay bar slides smoothly over the surface. 
Use a microfibre cloth to wipe off the spray detailer and move to the next section. 
Check your clay bar after your section and see what crusty crap is on your bar. 
After every section you should knead up your bar again so you have a nice clean section to work with!
Heres a mad tip too...
After you wash your car run your fingertips over your paint.. You will feel how rough it is.. 
Go grab yourself a plastic sandwich bag or the likes put your hand in the bag and feel the paint again. 
Let me know what you feel [emoji6]
Do that before and after claying the car to know if you have got all the surface contaminants off ready to polish her up!
Madd tips man thanks heaps i am keen to give it a go :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeah, the latter. No diff should have a centre replaced without checking clearances because its unlikely to be the same as whatever came out. Not that that stops most people just checking a new centre in
    • Major thread necro but how bad of a job is it to DIY? Looking at it online it looks like if you reuse your ring and pinion as long as those are in good condition it should be fine to just pull the axles/front cover and replace the diff that way? Or should I be replacing everything and doing preload measurements/gear mesh testing like the factory service manual mentions for the rear diff?
    • in my list I had the R33 GTR as the best Skyline. Infact I had all GTR's (33>34=32), the NSX, the GTO, the 300ZX, the 180SX, the S15 better than the FD RX7. I had the MR2 and the A80 as 'just' better. I also think the DC5R Integra looks better but this is an 01 onwards car. I also think the FC>FD. It's almost like aesthetics are individual! The elements @GTSBoy likes about the FD and dislikes about the 180 are inverse in my eyes. I hate the rear end of the FD and it's weird tail lights that are bulbous and remind me of early hyundai excels. They are not striking, nor iconic, nor retro cool. The GTO has supercar proportions. I maintain these look much better in person (like the NSX) especially with nice wheels and suspension which is mandatory for all cars pretty much. Some (or all) of these you have to see in person to appreciate. You can't write a car off until you see one in the flesh IMO. Like most people we probably just like/dislike cars which represent certain eras of design or design styles in general. I also think the 60's Jag E type looks HORRIBLE, literally disgusting, and the 2000GT is nothing to write home about. FWIW I don't think the Dodge Viper Gen1's have aged very well either. You can probably see where I rate bubbly coupes like the FD. I know we're straying now but the C4 and C5 absolutely murder the Viper in the looks department as time goes on, for my eyes. Wouldn't surprise me if people who love the FD, also love the MX5, Dodge Viper, Jag E Type, etc etc.
    • I used to hate R31s, and any of the other Nissans that led up to it, and any of the Toyotas with similar styling, because of the boxiness. They were, and remain, childish, simplistic, and generally awful. I appreciate R31s a lot more now, but only the JDM 2 door. The ADM 4 door (and any other 4 door, even if they are unique compared to our local one) can eat a bowl of dicks. The Aussie R31 is also forever tarnished by their association with stereotypical bong clutching Aussie R31 owners of the 90s and early 2000s. I think the Nissans of the 70s (other than 120Y/180B/200B) are far superior looking to the 80s cars. The 240K era Skylines are boss. The same is broadly true of Toyotas. Hondas don't ever register in my thinking, from any era. Mitsus are all horrid shitboxen in any era, and so also don't register. Subarus are always awful, ditto. Daihatsus and Suzukis also don't generally register. They are all invisible. I think the SW20 MR2 looks fiddly. The 3000GT/GTO is like that but way worse. Too many silly plastic barnacles and fiddly gimmicks ruined what could have been a really nice base shape. Kinda-sorta looks like a big heavy ST165 Celica coupe (and I'm not sure if that's a good thing or a bad thing). I think the 180SX is dreadfully bland. It's not bad looking. But it has no excitement to it at all. It's just a liftback coupe thing with no interest in its lines, and bad graphical elements (ie wide expanses of taillight plastic on the rear garnish). The S13 Silvia is a little better - getting closer to R32 shapes. But still....bland. S14? Nope. Don't love it. S15...a little better. Probably a lot better, actually. Benefits from not being like a shrunk in the wash R34 (where the S13 was a shrunk in the wash R32 and the S14 looked like a Pulsar or something else from the stable on Nissan mid 90s horrors). The Z32 was hot as f**k when it came out but hasn't aged as well as the A80. Keep in mind that I think the R33 is the most disgusting looking thing - and out of all the previous cars mentioned is objectively closest to my precious R32. It's just....real bad, almost everywhere you look. And that is down to the majority of what was designed in the 90s being shit. All Nissans from that era look like shit. Most other brands ditto. In that context, the FD absolutely stands out as being by far the best looking car, for reasons already discussed. Going behind the aesthetics, the suspension alone makes it better than almost any other car.  
    • If they just called it the "Mazda Tiffany", it would have been spot on.
×
×
  • Create New...