Jump to content
SAU Community

R33 gtst turbo to dump pipe gasket


Ty1
 Share

Recommended Posts

Good morning everyone! in the process of fitting my new turbo and just noticed that the wastegate flapper just interferes with the dump pipe gasket. Im not sure how far they open when under boost but do they generally open up this far? The gasket that was supplied with the turbo looked cheap so i purchased a new genuine nissan gasket instead. Also is it a big deal if the gasket sits over the flange by a couple of mm? 20171022_102610.jpg

Link to comment
Share on other sites

Not a big deal, but not ideal either.  I'd grind it back to shape....do you have a Dremel?

And what is the fit like on the dump pipe?  Is it also oversize on it?  If so the same issues will happen.

If it isn't then shaping the gasket is a waste of time. when I did mine I used a die grinder and cut but the rear housing and dump area down to a smooth 'same shape'.  I did the same with my manifold to turbo fit as well as my manifold to head fit.  ie no high points or obstructions anywhere.

Link to comment
Share on other sites

On the dump pipe, the gasket fits perfectly. No over hanging at all. Surely the wastegate flapper wouldnt open more than 90 degrees anyway. Will bolt it all up and let everyone know how it goes. [emoji120]

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Much less twat-tastic. CF wheels are too garish for civilised use.
    • From there, as the manual says....assembly is the reverse of disassembly, no tricks worth mentioning Much better (for me)
    • In my case, the standard wheel I had was in good condition but the buttons had more wear, so I swapped them across from the original wheel from the car. The plastic rear cover is held on by 4 tabs, and once the wiring is removed you can get access to 2 screws on each side the hold the buttons in From there I just swapped the wiring over. What was interesting is the standard style wheel is 2.0kg but the carbon fibre one is 50% heavier at 2.9kg. It even has a weight inside the wheel at the top to make up for some sort of imbalance in the design. weird
    • Once the airbag is off, to remove the steering wheel.... Undo the 2 plugs into the clock spring, and the horn connector from it's clip. Hit the 19mm nut with a rattle gun (preferably) or if you don't' have one, you probably want an assistant to hold the wheel in place while you use a breaker bar to undo the nut Then, screw the nut back on 3 turns, and pull the wheel sharply towards you. If that doesn't work hit it medium force with a rubber mallet on either side, or possible behind if you can get there. If that all fails (it shouldn't!) you might need a steering wheel puller
    • So, to next task....the carbon fibre steering wheel was either an expensive factory option or a chinesium special. Either way, I don't like either the flat bottom or thick ring style, so it had to go So...to remove the steering wheel.... First, disconnect battery negative and stomp on the brake pedal for a few seconds. Then, remove the small circular covers on each side of the wheel's rear surround to uncover the airbag clips. You need to push something like a flat bladed screw driver through, to push the steel clip inwards and pull the side of the airbag forward. Once you've done the easy side, same on the centre console side. You can see the tab you are shooting for circled in red Then, disconnect the horn spade connector and for the yellow airbag plug you need to get something small under the black locking tab to pop it out, then the connector releases......airbag is off  
×
×
  • Create New...