Jump to content
SAU Community

Recommended Posts

Got to clean out the garage

R33 GTR main gauges speedo tacho etc has 25,000klm on clock $200

R33 three centre gauges #SOLD#

R33 GTR fuel pump $220

R33 GTR injectors $280

R33 GTR AFM x2 #SOLD#

R33 standard intercooler pipes $80

HKS AFM pipes from AFM to air filter pod #SOLD#

R33 GTR clutch kit from unique autosports 40% increase in clamping pressure bronze cerametallic clutch plate done approx 3500klms new $850 sell for $150 ( check unique autosports webpage)

R33 GTR stock cam gears x2 $50 for both

R33 stock fuel regulator $20

make an offer you never know!

the three centre gauge consists off front torque,oil temp and a boost gauge

the clutch is a pull type ,i think 33gts is push so you might need some sort of kit to change it over to a push type setup other than that iam not sure.

I dont think so as the gtr injector is low impedence top feed where as a rb25 is side feed high impedence you would have to change your fuel rail . I think they are better suited to upgrade for the rb20 in the R32 gts.

CroatianDlite yes they are both for a R33 GTR they are the stock guages $280 for both plus postage

Blitz_R33 the clutch was only used for about 3 to 4000 klms over about 6 months it was taken out and replaced with a twin plate when i upgraded my turbos, unique autosports claim it can hold onto 300kw atw i never pushed it that hard only dropped the clutch 3 times running mid 12's and it never slipped, i would say it would have at an uneducated guess closer to 60 to 70% left in the plate iam not really sure and iam certian unique autosports could supply a new clutch plate if needed this is why i have it at this price

CroatianDlite yes they are both for a R33 GTR they are the stock guages $280 for both plus postage

Blitz_R33  the clutch was only used for about 3 to 4000 klms over about 6 months it was taken out and replaced with a twin plate when i upgraded my turbos, unique autosports claim it can hold onto 300kw atw i never pushed it that hard only dropped the clutch 3 times running mid 12's and it never slipped, i would say it would have at an uneducated guess closer to 60 to 70% left in the plate iam not really sure and iam certian unique autosports could supply a new clutch plate if needed this is why i have it at this price

Interested in the 33GTR centre gauges. Do you know (or does anyone else know) if these will plug into an R32 GTR?

Thanks,

Richard

OK

mmmgtir i wouldn't know i dont think R32's have the front torque meter on them do they?

Blitz_R33 postage looks to be about $25 from Townsville to Brisbane the weight is around 20kg

Stirlo_GTR Sorry the pipes have been sold

  • 2 weeks later...
OK    

mmmgtir i wouldn't know i dont think R32's have the front torque meter on them do they?

Blitz_R33 postage looks to be about $25 from Townsville to Brisbane the weight  is around 20kg

Stirlo_GTR Sorry the pipes have been sold

Yeah they do, they have the same three gauges, only difference is that the R33 ones are angled slightly, I'm just wondering if the plug etc is the same?

Richard

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There aren't boost creep issues, it's not engineered around the restriction of the cats but if you haven't tuned the engine a full decat + exhaust can flow enough air to run off the end of the OEM load scales and you will get a pretty substantial reduction in ignition timing as a result. I recommend using DFCO, avoiding ignition cut limiters, and avoiding popcorn tunes along with running a cat unless you enjoy a perpetually soot-covered and potentially burnt bumper.
    • Small update, it's been slow moving over the Christmas period with money having to go everywhere thats not my car 😅. I got myself a little present to myself from "santa" in the form of some tidy radiator mounts from fitmint automotive to get rid of the stock ones that look like they have been in an accident before and then straightened by a caveman. I know I should've replaced the rubber bush at the same time but I had no idea how bad they were until I was replacing the mounts. Decided to order their dash mat while I was at it as I feel like I am lucky enough to have a pretty decent condition dash and I don't want to risk it being ruined while it's parked in the aussie sun while I'm at work. I have found another electrical fault to add to the evergrowing list to eventually chase down. Every time I replace my taillight globe it blows within a day of use, I'm starting to think my life would be easier if I took a few minutes to learn how to use  a multimeter 😂.   Had some luck with finding a series 2 drivers headlight on marketplace to replace my mismatched series 1 headlight, a subtle difference but it's nice to have a matching set of lights now.   I returned to the air con problem due to being sick of this summer heat, found a good condition condenser to replace my leaking one! I got it in the car and was happy when I got the thumbs up that the system was now holding gas. Sadly the compressor is not kicking in for some reason, we even tried branching the relay in the fuse box. I have tried to do some research on the issue with no clear understanding of what the fix is, so for now it will be placed on the backburner until I can be bothered to look into the wiring to the compressor. The last small mods I have done was cutting the horizontal vents out of the front bar, not really in a functional airflow sense but I just think it looks better as I am not a fan of the series 2 bar. I also switched the shift knob out for a hosoboyo aluminium grex style one, it has a really nice more direct driving feel than the outdated rubbery oem one. Thirdly, I chucked on one of the ebay bonnet strut kits. The fitment is decent and they seem to work fairly well. They have only given out once while the car was parked facing downhill, I think if I was working under the bonnet I would still put the oem hood stay up to be precautionary as to avoid getting a speedy concussion.
    • Got pneumonia, haven’t played with her in a while, but I’m back now. Previous owners cut bonnet pins into the bonnet. My choice try find a replacement or spend $15 get some pins myself to cover up. Now only one small hole to cover. looks shit now, but when the bonnet is red again. Be good 🤞
    • No R32 GTSt had 15" wheels. 205/55-16 was standard GTSt fare. 4.36:1 is standard R32 turbo auto diff. I think the manual was too, not 4.11. 4.11 and 4.08 were R33 namual and auto respectively.
×
×
  • Create New...