Jump to content
SAU Community

R33 gtst bogging/ misfiring? when losing traction.

vxsr33

By vxsr33,
in Engines & Forced Induction

 Share

Recommended Posts

vxsr33 Proficient

vxsr33

Posted
Posted

Hi SAUers

 

Firstly i do not condone irresponsible driving on the street.

 

I'm having an issue whenever i do a burnout or donut (done on private property) the car will start to bog and lose power within a few seconds (I'm not limiter bashing or anything), almost as if the ecu is dumping in heaps of fuel. This is the only time this issue happens, other than the motor runs well never misfiring, bogging or hesitating under load. I'm running a power fc and the car has been tuned by Chequered Tuning with no changes after the tune.

 

Any ideas? I had a search but couldn't find anything similiar to the issue im having.

 

Thanks for any help or suggestions.

vxsr33 Proficient

vxsr33

Posted
  • Author
Posted

It's not lack of throttle thats causing the bogging and i don't think silicon lube will help in this case. AFM is a z32 and car is pushing just under 260rwkw so i assume the AFM should be no problem. I want to do a beginners drift day hence why i want to fix the issue. The odd thing is it happens only after a few seconds of losing traction so it's not as if the motor is being abused and overheated. Could it be something to do with the tune? Should i contact chequeredtuning and tell them the problem or no point?

vxsr33 Proficient

vxsr33

Posted
  • Author
Posted

GTSboy what do you mean by get something to log the ecu? I don't have access to any tools like that.

CEF33Y fuel level has been around half way or a bit over. Ive never had any fuel surging issues. Pump is a walbro 255 wired up to a relay.

GTSBoy Grand Master

GTSBoy

Posted
Posted
  On 10/11/2017 at 5:56 AM, vxsr33 said:

GTSboy what do you mean by get something to log the ecu? I don't have access to any tools like that.

Expand  

Assuming it's a tunable ECU, then whatever laptop + software is required to talk to the ECU and log its operation, is what I meant.

  • Like 1
89CAL Grand Master

89CAL

Posted
Posted

Talk to Chequered Tuning about it, they seem to be good from what I see and you never know, they might pull up your tune and be able to see what is wrong without even having the car there.

Otherwise, as above. Get someone to watch what it is doing when it happens. If you have a hand controller and someone who has half an idea you may even be able to pin point it off there. They may have put a large amount of safety in some cells when they tuned it, and its not in a cell you normally hit day to day driving but when there's a different load (i.e. Burnouts) then it just touches these cells

I'm just guessing. If you have a hand controller log injector duty and timing then see if it spikes or drops when the fault happens. You can log airflow as well but I think something like injector duty or ignition timing will give you more of an idea

  • Like 1
  • 9 months later...
vxsr33 Proficient

vxsr33

Posted
  • Author
Posted

Spoke to chequered tuning about it a while ago (still haven't fixed issue) and they said the only way to fix the issue is to relocate the z32 maf to the cold side of the intake piping, between the intercooler and the throttle body.

Has anyone had to do this? [emoji53]
Would assume the maf wouldn't last long under boost pressures.
I'm still thinking it's an issue with the tune

Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted
  On 17/08/2018 at 3:28 AM, vxsr33 said:

Spoke to chequered tuning about it a while ago (still haven't fixed issue) and they said the only way to fix the issue is to relocate the z32 maf to the cold side of the intake piping, between the intercooler and the throttle body.

Has anyone had to do this? emoji53.png
Would assume the maf wouldn't last long under boost pressures.
I'm still thinking it's an issue with the tune

Expand  

Use a HPX MAF or a R35 MAF/AFM on the cold side

Then change the K constant to suit, works very well.

GTSBoy Grand Master

GTSBoy

Posted
Posted (edited)
  On 17/08/2018 at 4:49 AM, Dose Pipe Sutututu said:

Use a HPX MAF or a R35 MAF/AFM on the cold side

Then change the K constant to suit, works very well.

Expand  

This.  The smart way, and Chequered should be able to handle it.  It's not as easy on PowerFC as on Nistune, but still doable.

*edit* I somewhat missed the fact that it was a PFC when I responded the first time this thread came up.  But it's there.

Edited by GTSBoy
Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted

Could also be your throttle enrichment at higher RPM, it's so rich it is causing it to bog.

There's a table on the PowerFC to correct that, much needed trial and error with a wideband to get it right.

I generally aim for a 0.5 AFR dip

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Pete_Repeat
      V37 wreck

      By Pete_Repeat · Posted

      Good points thanks. Unfortunately I can't seem to rename this or delete the topic. Seems like I'll ask the moderators to change it or delete it.
    • sonicii
      V37 wreck

      By sonicii · Posted

      You might want to update the thread title.  V37 ≠ V36.  And it probably isn't a G37 unless it is 2012+ Ininiti or LHD.
    • LaurelPWR
      Rb26- Enlarging Std Throttle Bodies

      By LaurelPWR · Posted

      Just a basic run down of the relevant bolt-ons. All e85 First graph 406.9whp is HKS GT-RS, HPI manifold, 3" bell mouth dump / 3" straight through fake cat / 3" all the way to the rear and no resonators, nismo 740cc, walbro 460, oem RB26 itb's, power fc, eboost2, Greddy Spec M fmic, poncams, Turbosmart actuator, splitfires, ARD 150amp alternator. Blue line is same as above but Blitz Dual SBC (before i upgraded to eboost2) and 100cell "high flow" cat. Red line is after installing eboost2 and the fake 3" cat (it's just a 3" pipe with a cat shell welded onto it). Huge gains in response, as can be seen. Black dots are a mates sr20 with almost identical setup but uses a garrett 2871 instead oh HKS. Next grapghn 466.6whp is same as above, but HKS 2835 Pro S with the larger .87ar turbine housing, the special HKS Pro S dump pipe into a HPI split dual 2.5" front pipe and the rest stayed as is. Red line is after I welded the actuator brackets. (It was originally bolted together and was moving a couple millimetres under load). Green line is obviously before I welded the bracket, no other changes. 100whp gain at 3750rpm, massive gain for such a simple fix. Third graph is my current setup, huge changes. 469.7whp R31house twin scroll manifold, twin TiAl 38mm gates, Forced Performance (USA) HTA3076 with 1.01ar twin scroll rear housing, Link Fury+ and loom by 12volt, PRP trigger kit and r35 coil kit with r35 splitfire coils, HKS step 1 vct staggered cams, new oem lifters and performance springs, 49mm itb's w/port matched Nismo plenum, twin walbro 460 surge tank setup + 1650cc injectors, HKS Type R S13 600x300x103mm fmic, individual egt's, 4" turbo back with no resonators or cat and AES true straight through muffler + 4" butterfly off the dump pipe lower 90° bend. It's a preliminary tune with no boost control with using 20psi gate springs and 4" butterfly closed. Once body loom and PDM is compete, will go for 30psi tune.
    • joshuaho96
      Shifting questions

      By joshuaho96 · Posted

      Power light apparently functions as a transmission error light, you can try the power sequence to read any codes from the transmission control unit.  
    • MrStabby
      R32 GTR front coilover bottom mount - flared side in or out

      By MrStabby · Posted

      Agreed - looks better that way
×
×
  • Create New...