Jump to content
SAU Community

Recommended Posts

My R32 GTR currently has Reimax 60mm front pipe (was told 65mm when I bought it), but the Tomei dumps I recently had installed have 68mm exit.  Is it worth spending a few hundred getting a 70mm front pipe to match the dumps?  Will I loose low end torque with a bigger front pipe?

Also the Reimax front pipe has 80mm exit, but previous owner had a 76mm straight pipe installed.  Is it worth upgrading to a 80mm straight pipe?  The cat back section is also 80mm Reimax with 115mm tip.

Inputs appreciated!

Link to comment
https://www.sau.com.au/forums/topic/473554-r32-gtr-front-pipe-question/
Share on other sites

Just watched it, very good info.  So going big decreases back pressure, but too big will also decreases velocity and decreases scavenging effect.

How about equal length?  There are half a dozen choices out there, some equal length some not.  For an NA engine equal length is likely important, but I'm not sure about turbo...

Should I also spend another few hundred for a 80mm straight pipe to replace my 76mm?

This is why twins are gay.

Single turbo, full divided housing, full divided manifold, equal length manifold is the only way to harness the scavenging effects. Less heat due to less restrictions, less piping, less blown 2nd turbo (because it doesn't' exist).

But back on topic, just go massive

No large power benefits to equal length more so the sound. The sound above 5000rpm with a equal length sounds HEAPS better than non-equal. Turbo engine you just want to get rid of the gases as quick as possible, bigger the better.

  • Like 1

Is there a brand preference?  Because the price range is really wide, almost 3x difference between highest and lowest. 

Mine's ¥72,986, HKS ¥54,481, HPI ¥45,678, Greddy ¥27,210.  All stainless steel except Greddy, which I think is mild steel but painted.

https://www.rhdjapan.com/mine-s-front-pipe-pro-stainless-steel-bnr32-bcnr33-bnr34.html

https://www.rhdjapan.com/hks-stainless-front-pipe-bnr32-bcnr33-bnr34.html

https://www.rhdjapan.com/hpi-single-front-pipe-bnr32-bcnr33.html

https://www.rhdjapan.com/trust-greddy-mx-front-pipe-bnr32.html

Yeah I saw the Midori front pipe too, but it is one of the few that is not equal length.  (and most titanium ones are not equal length)

I end up buying Greddy, which is cheaper but still equal length and weights slightly less than others because it is not stainless steel.  Where I live I do not need stainless steel anyways.  I also bought Tomei's titanium straight pipe.  Will see if anything improves after I have them installed and dyno'd during the next couple months.

Really?  Google Translate says it is :8_laughing:

http://www.trust-power.com/products/exhausts/greddy-mxフロントパイプ/

Product features

It is a front pipe pursuing smoothing of piping and optimization of pipe diameter. 
By improving exhaust efficiency, exhaust gas resistance immediately after turbocharger is greatly reduced, and efficient supercharging is promoted. 
For RB 26 DETT, it is designed to increase the exhaust efficiency by using exhaust pulsation by equalizing the length from the turbocharger to the collecting section.

I will measure it once I receive it to see how big is the length difference.  I will weight it too.

I didn't get HPI because they dent their pipe to make it fit (says so on their Japanese website and it shows on their product picture) instead of designing to make it fit.  HKS has 85mm exit, and my cat back section is 80mm, I didn't want to create another step down.  Midori is a true non equal length (at least Greddy tries to fake it).  https://www.rhdjapan.com/midori-seibi-center-front-pipe-sus-80mm-bnr32.html  Mine's is just very expensive and is made to order so will take a long time.

I bought mine from FRSport.com, they price-matched another webste so I paid $314.40 USD shipped.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Pfft. As if I'd ever point a high pressure washer at my car.
    • The nature of my commute has changed. Way back then it was traffic lights all the way, for ~28km. It sucked. When they finally stitched the expressway together I could do a good 15+km of it at a steady 80-100 with no stopping. That alone has gotten me down to flat 10s. Prior to that it was mid-high 10s. I can't remember the delta that I saw when I got the idle down. It was only ~150 rpm, because the idle speed was never terrible, but for the delta in consumption to be noticeable it would have had to have been at least 0.2-0.3 L/100km - which is not to be sneezed at when it comes for absolute free. It's only about 50L per year, but that's ~$100. A few extra pizzas is always welcome. Note that I have a record of every tank of fuel that has ever gone through my car except for a handful put in by someone else, like my mechanic. I can show you the difference between stock RB20 and tuned RB20, stock RB5Neo and tuned, winter and summer fuel blends, winter and summer fuel blends when the ambient temperature is not appropriate for the blend, working O2 sensor, blown O2 sensor, boosting f**k out of it and frightened to boost it because it is pinging, and so on. OK, I probably can't do all that now with 100% clarity - but at the time when any of those things were in event, you could see it in the records. There's 25+ years of simple tank after tank records, so you have to look for landmarks to work out approximately how old any single record is. What's really important is the meta data and that lives in my head.
    • If you're claiming the issues are not skyline specific, then either the USA is living in the 90s / early 2000s, OR you have the issue of "survivor bias". Which is you're mainly hearing and listening to those with terrible experiences, and haven't found the guys who have cars with good decent builds and no problems. It happens in AU too, that plenty of people keep having issues, and they keep going to the workshops that are known to be shit "because I read on the internet". Even worse, are those who keep posting on the internet as though they know for a fact what something is, when they've never touched/looked at said item in their life, and again are making assumptions, based on something they read, or because it's a certain way in other cars. It's even funnier when those same people debate the facts with the people who've lived and breathed this stuff for over 15 years. Example, I've had someone tell me you can't do something with a Skyline, because they read it on the internet, except I can tell they're wrong, as I did that exact thing back in 2008 with my Skyline.
    • The funniest part I saw, was someone would bitch and moan on FB about something, Andy would be the one to respond, asking for more info, if he could contact them, what the engine setup is, what their config file was, and 95% of the responses were people just going "der! It doesn't work" and Andy going "What doesn't work?" And then going "The firmware!" And they'd go around in circles as no one could ever give information, and Haltech couldn't fault things on the bench, (especially when people wouldn't give any specifics).   Many moons ago, when Andy was back at e420c stage, he reached out to me, and asked me to test different plug and play looms for him (already had an e420c in the car on his V1 PNP loom). And he kept asking me, as I was competent enough to be able to give him some specific feedback on what was/wasn't working, how to replicate the faults etc, and work through things with him. Most people are terrible at answering the questions they're asked, or being able to provide quality feedback other than "it doesn't work".
    • I say it often, none of this stuff is really Skyline-specific per se. But in general there's not a lot of people who actually know what they're doing. A lot of people charging like they do. Agile software development probably isn't the greatest idea for an engine controller.
×
×
  • Create New...