Jump to content
SAU Community

Recommended Posts

hey guys, need some help.

was helping a random guy out to save him a long walk with his suitcase, when he put his suitcase in the boot he slammed it shut as hard as possible. now the boot it stuck and I believe the valet switch has moved down.

now the shit part, the previous owner of the car removed the key from the rear of the boot so you can only open it with the lever. it still has the rotating Nissan badge, but you can just see straight into the boot from the hole. so key is not an option.

I have taken out the back seat, taken the access panel off, but can't get to the switch because the guys suitcase is in the way, and the smart fellow put it on its side instead of flat so I can't go over the top of it to find the valet switch. 

I don't know exactly where the valet switch is in the boot, so if someone could take pictures. ones that are not direct close ups so I can try get at it with something long, just need a better idea of where the latch is.

other pictures I've found are all close ups.

sorry for disorganised post, written on my phone in a foul mood and in a hurry

Link to comment
https://www.sau.com.au/forums/topic/473725-r33-boot-stuck-valet-switch/
Share on other sites

I had this same problem and ended up just removing the 3 10mm bolts from the boot latch locking mechanism with a shit load of extensions on a ratchet and then lifting boot open.

The valet switch is behind the plastic trim at the bottom, you have to flick up a little plastic panel to access it. Mine was jammed, so i did the above.

You could try getting said idiot to pull the boot release lever while you try push/pull the valet switch with the coat hanger. Pulling the boot release may make it easier to move the switch.

If you stick your finger in the empty lock hole, can you feel a little rod sticking out?
If that rod is there, pushing that to the side should release the boot too. Thats what the key lock basically does.

59 minutes ago, toldfield said:

Nope, hole is too small to get a finger in, but looking in you cant see anything either, just a tunnel with a slot cut out at the bottom.

previous owner removed because apparently it was easy to break into, so he says.

Obviously all he need to do was jam a suitcase in there lmao.....sorry

  • Haha 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • This was a huge help.  We followed the steps,  although shifting into 2nd was actually into 3rd for us,  and 1st was into 2nd ( steps 9 and 11) .  The long flash was the 4th flash.  So shift solenoid A is possibly the culprit.  Is this inside the transmission itself? Or is it accessible by just front the pan? Or is it bolted to the outside of the transmission?  Thanos for your help everyone
    • Can you enlighten me on your best practice regarding these hoses? I don't wanna make the same mistake if you already got a better solution.
    • I have some silicon hoses already, for example engine to watercooler. But yeah, I get the sentiment. The lower intercooler silicon hose is drippy too, despite not being very old. Does anyone except Nismo make these same lines out of rubber? Long term I think they'd be the better replacement, especially since the car won't live as hard a life anymore as in the past nor be driven as often.
    • I know most issues are just age related. But for example the turbo oil drains, there is dash adapters for these and you can just make a braided teflon line for them and (probably) never have them leak again. Also not terribly expensive. Can you even get the factory hardlines from new? Or are they repairable if they break?
    • I know it'd be much much easier with the tool. I hope I can find one that won't take 3 weeks to get to me an isn't a "Asian models kit" that has tons of (to me) useless adapters for a load of cash.   It's a summer project/fun car. I do wanna enjoy it, without endless downtime over and over. So yeah I would even go and buy an engine crane + stand to save myself the trouble of hard to reach or unreachable places going bad later on. Would also be a good opportunity to put on a Fluidamper, renew the mains seals and stuff like that. I have some money on the side that I can use for that, what I wouldn't want to or be able to do is let everything be done by a shop or have my engine completely rebuild right now. I intend to do most of the "doable" jobs myself. Pulling an engine can't be that hard, can it?
×
×
  • Create New...