Jump to content
SAU Community

Recommended Posts

Hi guys,  i'm here to find out if the front diff+sump of the r32 GTR will bolt straight onto my 1990 r32 gts-4 as well as the rear diff from the r32 GTR.
My current rear diff has blown up due to running on no oil and I cannot not find one with the right ratio to replace it so im looking to swap out both for the 4.11:1 from the GTR. 

Thank you 
 

Link to comment
https://www.sau.com.au/forums/topic/474090-r32-gts-4-diff-help/
Share on other sites

Yes, gtr sump (and diff) will bolt straight on a gts4 (noting it is effectively an engine out job).  At the rear the drive shafts will be different so it would be easiest just to change the diff centre.

  • Thanks 1

I myself thought that the R32 GTS4 had the same 5 bolt diff flanges as the GTSt.  Someone on here (just the other day) swore black and blue that the GTS4 diff was the exact same 6 bolt setup as the GTR.  I myself find this hard to believe, because the GTS4 has the same shitty VLSD centre as the GTSt, not a mech diff like a GTR.

This confusing nonsense does not directly help you, but shows that I agree with Duncan that the GTS4 rear diff is not an easy swap with a GTR diff.  You should get under your car and take a photo of the diff and flanges for us to make this the=read a useful and searchable resource for the future.

well there you go.

rear is straight swap then (if there is a pair of ABS sensors on the diff end of the half shafts), but and so is the front...there is just a lot of work to change the front diff/sump....

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Sharing results from recent Liberty Walk R35 GTR, since they are still considered as somesort of a V36 Skyline. We do them turbos too. This are high flowed SS-1 models with ball bearing conversion done.  Car have managed to pull 485awkws @ 20Psi so far pushing limitations of factory built engine. The build list for R35 GTR enthusiasts as follow : HyperGear high flowed stock turbos in SS1 (G25-660 specs) Custom titanium intake pipes. Vspec performance titanium front pipes. Vspec performance 4" titanium exhaust. Upgrade fuel pumps. 1200cc injectors. Ignition coilpacks Hks intake plenum. Hks intercooler piping. Greddy intercooler. Greddy bovs. Top-secret coolant reservoir. Emtron ecu. Straight E85. Built gear box.  
    • Nah no bearings, just slip fit.  Would be a reasonably challenging but not impossible job to modify it to run bearings but I'm hoping that's not necessary as I may have well built one myself if I end up spending hours modifying it!
    • Brumbys with good shells are bloody expensive, I've looked at 2 "cheaper" cars, and walked away from both,  plus after some research spare parts are fairly sparce I'm starting to think that I missed the boat on finding a clean one that is straight (ish) and without alot rust I'm starting to think about a old Hilux as panels and other parts are much more available as they sold tens of thousands of them I use to be indecisive but now I'm not sure
    • A Brumby would probably fit a big metal toolbox in the back... this is how it begins  
    • Picked up a new OEM boot seal for the MX5 today as the old one got ripped a bit by me being a idiot by seeing if I could fit a large metal tool box in it, it didn't fit, and ripped the seal with the corner of the tool box I am still waiting on time to get the cams and new balancer installed, as well as the repairs to the boot Time will not be an issue soon though
×
×
  • Create New...