Jump to content
SAU Community

Recommended Posts

Hae all so im replacing my wheel bearing on my 1993 r32 and its been a complete nightmare. So i originally bought a bearing off ebay for a r32 as pictured451394808_Screenshot_20180611-174953_SamsungInternet.thumb.jpg.ee0f9ae64a3cbda25b225d1ae02e52bd.jpg

Then once apart i come to realise its wrong and its this type20180611_173717.thumb.jpg.1028eb28a7d1684f5009aa3c71c4a3a9.jpg

Now after alot of searching i come to the assumption i have a type m? Because i have 4pot brakes on front 2pot on the rear and digital climate control. i eventually found a bearing through bursons it came up as a r32 gtr drum handbrake type so i got it, fitted it up and the inner diameter for the cv spline is to big. Can some one please tell me exactly which one will fit because the lady at bursons said there were no other listings for a 32 apart from what i bought from them and the original one i bought. Need one by the weekend. Thanks 

Link to comment
https://www.sau.com.au/forums/topic/474302-need-help-with-r32-bearing/
Share on other sites

Assuming your car is 2wd (since you don't say, and neither does your profile) not 4wd?

When you say you "fitted it up and the inner diameter for the cv spline is to big" do you mean you can't press the hub face back into the bearing because it is too large, or because it is too small/loose or something else?

If you post up your VIN# someone can look up the exact nissan part# in FAST for you.

9 hours ago, Duncan said:

Assuming your car is 2wd (since you don't say, and neither does your profile) not 4wd?

When you say you "fitted it up and the inner diameter for the cv spline is to big" do you mean you can't press the hub face back into the bearing because it is too large, or because it is too small/loose or something else?

If you post up your VIN# someone can look up the exact nissan part# in FAST for you.

Sorry it is a 2wd and it came as a hub and bearing assembly. So when i went to push in the cv shaft it just spins without meshing to the splines

1 minute ago, Duncan said:

Ok...so you are correct, it is a type M.

Sik_R31 was the winner, part numbers you need are:

43280-30P05 / 43280-AA000, and

43281-30P05 / 43281-AA000

 

Excuse my ignorance but whats Sik_r31? 

Those part numbers will i be able to use to them at a place like bursons? 

sorry, Sick_R31, not Sik_R31

On ‎6‎/‎18‎/‎2018 at 10:24 PM, Sick_R31 said:

Bursons may not be able to use those numbers, they are a Nissan part number so they would need a cross check. You could buy from Nissan or Kudos as per Sick_R31's link. Or Amayama.com if you are not in a rush.

1 hour ago, Duncan said:

sorry, Sick_R31, not Sik_R31

Bursons may not be able to use those numbers, they are a Nissan part number so they would need a cross check. You could buy from Nissan or Kudos as per Sick_R31's link. Or Amayama.com if you are not in a rush.

Alright sweet as thanks heaps ?

  • 3 months later...

Bumping this thread, trying to get out the hub out from the knuckle after removing the entire assembly from the car...

I clamped the knuckle to a piece of wood, stood on it and went at it with my sliding hammer as hard as I could. Nothing besides me and the entire knuckle/wood thingy moved a single mm.

Just want to verify, the snap-rings are only there to hold the bearing, right?

Any options besides more heat, more lube and more force?

asda.png

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Oh, that's grim. Something bad has been happening there.
    • Put an endoscope down the hole and saw this. Not quite all around the bore but a good 60% at least. Chin to the chest and towards further disappointments I guess.
    • 2 does "sort of" applies, maybe......but looking at what parts would be needed for the swap to get engineered, registered, and insured, and basically that's everything under the car, the modifications the make it legal would be problematic and horrendously expensive, all for a street car that just cruises around and hits a few twisty roads on the weekends Also, from looking at the NSW rules and Regs, with all modifications that is required just to make the car safe and not twist itself to pieces, and then actually get registered for street use, may still be impossible nowadays As for 1, when you add in a fresh engine, fresh transmission, rear cradle and diff, tailshaft, suspension, brakes, cooling, and all the other fabrication required, your probably looking at up to $100k to do it right, all for a 20 year old MX5 that is over engineered and you would never be able to actually use the power it has on the street, much like your beastie, which I love, but you actually track that thing and can use all of its powers in anger, in a safe environment  Hell, the old Bogan Cruise Ship had more power than I could use on the street, and in hindsight, I went a bit silly on that thing, it didn't really need the 500hp it had for what I actually used the car for, it was fun, but basically unusable on the street if you value your licence  As for cams, yeah, I'll probably book it in for them to get installed and tuned soonish, like next month after MX5 Mania are back at work....... and yes, I've already sent a email to bin the turbo quote and quote instead to install cams and a new Fluidampr balancer that will suit the 2.5 better than the OEM 2.0 balancer that is swapped over for the 2.5 install, as the balancer needs to get pulled to time the cams it's a while your in there sort of thing I did think a bit about flex fuel for a laugh, but being na, and no where really around locally anymore to get E85, I've binned that idea, so no sweet sweet corn smells are set for the car I wish E85 was more of a standard fuel, it's better for the environment, better for tuning, plus that sweet sweet smell we all love As for fitting in the family, that's not needed, as everyone in the family already owns a car that can seat 5 humans comfortably enough, the MX5 is "my toy" As for buying a car that is already built, nah, I would rather pick and choose my parts, I enjoy the process, and in the big picture, the additional cost is well worth the enjoyment, and the occasional frustration, I get out of doing it, albeit with other people spinning the spanners, and me, just paying the invoice 🤣
    • Excuse me, but 2) does apply 1) Would also apply if you consider how much is spent in the alternatives. Also there's the option of 3), buy one pre-built that you can put your family in (it's me, it's my car)   That said, I went on a ~500km drive the other day. I didn't use anything more adventurous than 3rd/4th gear at about ~3000RPM and 50% throttle and I was going as fast as anyone has any sense doing on a public road, with enough grip to the point where I didn't want to go any faster. I was obviously under the limit of the current car etc etc. MX5 with 2.5 N/A to achieve the same speed would be more fun for any road scenario. Maybe consider cams. I wouldn't boost it. The use case is just not there and it won't actually make the car more enjoyable unless you really do plan on wringing gears from 1st to 3rd (at least) at 100% WOT on a public road to 150+kmh.
    • Great if: 1. You had all of the money for everything else that is required  2. Lived in a country where you could actually do this and drive it legally on the road Sadly, neither applies to me As for the turbo, I am having second thoughts, mainly for engineering/registration legality reasons and insurance  Not saying I've finished doing stupid things that I probably should do to the MX5, but boost, and V8 engine swaps isn't on the cards Strange, but true 
×
×
  • Create New...