Jump to content
SAU Community

R33 GTR gas boot struts

sleptema

By sleptema,
in General Maintenance

 Share

Recommended Posts

sleptema Proficient

sleptema

Posted
Posted (edited)

Just wanted to share with everyone some concrete information regarding replacing boot struts on R33 skyline, specifically the GTR but I am sure the information will be transferable. The reason I am posting is that there wasn't much information regarding pressures & the ability to remove the strut from the bracket (requiring drilling).

What I did ended up costing me $110.

Below is a picture I pulled from another thread, this is the part of the strut that is hard to remove. Very hard, but not impossible. What we did was use my 10mm spanner and wedge it in between the ball and the strut, then slowly work the it off. It looks like it's going to snap the strut and it ends up destroying it, but that's ok because new ones are cheap.

boot-struts.jpg

This is what mine looked like in the end.

_l_YlkhMrhBQ8EuTW0y2zCoronteQxKCJER7sheMowcDwPIacsgt8UsL1x21IK-aTNXtvJXg3_kDwKUO7ncCs5DhF97OgP03zCT2utJVgpasCM6swm6c6yBZghppOjRhrCDRNymusekRCAFCSLVeDDiJm-IyBLP34tFaLLj8iCNpO2l6-UBwXrdBHA8BrnRC2PnUvzFoIlPfql9mXz8kCw2L9ytvHw6U1scTkSBwqeMqsIX3wNksn_sPAbpZy7Kvlh3mOQGX7KphM2zUYUYY7fQyb_6DonTPI7HHveh-rqFTAxWNHIakGcNYvps9VAVQj_mvLAeoAlYLLJc-G9y9JH0t6EtBHhm5yN24o8_VHlDPboaZSpn4JoPdTUqAsb1Bh6kMrn--BwO5A_lftYEt7veVc8Mlg_eRZDr1nmb-pRaFW7WM8t08Ovg1xyN9jqbzhrRYS7wM9y4AxFwLHATXOaDlynuPHkZcUgY0ibAGwO6JeF_uLZs7dOxy4wcKj_m3rfQvjU6XJDkOfYiD5s24OyPnXqpZlMiQAxzc1wHM3VbEVKYgpPWqY3Ai_QBEcx5qndaGyljSAFyMJYY8KCQYhf5Icq7Vf4hdq6ORlGA=w731-h974-noMO_Ysbf9qqSSN3mh_W5cj--ZVZTDnQEdrg71b3qAL6ClwNPe2BAzRm9ffXwQtLNShfvVSrGZb1awzrTs-3wsiEDqajZLPoN-XH-oo3yrhDvt5S_iPPMs7CTedRr8Y9WVnNO4f4jH3znvJrerLZKaR1GZUm0gc0JunMDdDGBD_5Lga0DDMfHnarSUZq363IDwK97xkihWKBzrJRQAwiFYQw5j1Z9Dnv164W7OSwGE4XGxZ2eHIXysSShGk4IjHd_zD9SavOpyaH66YFmaVk38ecHVh0F1n5WLR9v8cqwuRQWMUZFyBWKd4hFCiprRS1wRgHjT9Iq1NS14jwjcKH2J9ydIEwV-D0wFsaZ5iPU1TVRZbW64atB04SPiQLer1iaCjN8IQuaboBUJBroqU-fMS23BF47Nh-odqGUvevbRwZJlZq-y8SrFnzt4yEWXv_Gd9q3ynKsZF2BcZsbcgSnhLdmijitWj445px4bXxpp9G_r_3lYpT3DMNRp0q12ksFoBKJ-o1_dLONJpkt8z3TBNpHHgJpGpvqu1omhtPLvdPN8GYOocaBcbO6StAmCCNv8PSKanLGhsXMwgLBHVr5axmsFFRB284OaLppLBXg=w731-h974-no

We ended up putting 100nm of pressure in each cyl. It holds the boot fine with a genuine GTR spoiler. If I had to do it again, I would put 150nm in each to see if it holds any better, BUT that 100 works just fine.

Any questions please shoot them through.

Edited by sleptema
  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/474449-r33-gtr-gas-boot-struts/
Share on other sites
GTSBoy Grand Master

GTSBoy

Posted
Posted

What's 100nm in real pressure units?  You have given units of torque.  Pressure is measured in Pascals or multiples thereof (like kPa, MPa, etc) or in psi for knuckle dragging 'Muricans.  Or in N/mm2 (equivalent to MPa) or in bullshit units involving the heights of columns of fluid such as water or mercury.

sleptema Proficient

sleptema

Posted
  • Author
Posted (edited)

Yeah sorry guys, I was thinking about that this morning and realised how stupid I must sound aha. The guy who did my struts didn't correct me, I believe it would be newtons.

EDIT: Re-uploading pictures of finished product.

IMG_20180707_111049.jpg

IMG_20180707_111053.jpg

Edited by sleptema
  • 4 weeks later...
  • 4 weeks later...
Tamorus Enthusiast

Tamorus

Posted
Posted

Hi all,

I am also keen to know where I can buy these as I have been looking and found nothing except a few used struts on eBay.

Any help would be appreciated...Every time I need to use my boot at the moment I feel like I have my head in a guillotine!!

sleptema Proficient

sleptema

Posted
  • Author
Posted
On 7/31/2018 at 12:02 PM, Ty1 said:

Where abouts did you get this done? And these are new struts yeah? or did you end up managing to reuse the factory ones?

I used a generic strut specialist. Old ones needed to be thrown out as there was no way they could be re-used. He just used the brackets from the OEM ones and adapted them to fit on the new struts.

I believe he just measured the extents of the struts and ordered accordingly, and put above mentioned pressure into them.

  • Like 1
  • 8 months later...
Fastlane Contributor

Fastlane

Posted
Posted (edited)

Hello

my Gas Strut were weak so I want to replace them.

This Topic pointed me in the right direction, thanks !

You can chosse this Model from Mercedes Part No.: 2218800329 

It s from the W221 S Class Hood strut.

You can find them for around 14$ on Aliexpress. They are a little bit too strong so I recommend to buy some used ones.

I only replaced one and the Hod stays in any angle.

I recommend to tap an M6 in the Bracket and add a nut to secure the strut.

They are a 14mm  to short, so the Trunk opens 12 cm less. Adding a spacer will fix this

I also replaced the rubber bumper . They are from Aliexpress also.IMG_2323.thumb.JPG.afe41b4eae5716055d1b1a494c668e28.JPGIMG_2326.thumb.JPG.1e7e979e952d3c797bb5eeadcbb3328a.JPGIMG_2328.thumb.JPG.0afff9f21876085c3da8d913c770010d.JPG

IMG_2327.JPG

IMG_2325.JPG

Edited by Fastlane
  • Like 1
  • 3 weeks later...
Fastlane Contributor

Fastlane

Posted
Posted

So I did some research, cause the Mercedes Strut were to strong

The original USED Struts have 30 kg while pushing and approx.20-25kg while holding.

The new ones should be around 35kg-40kg

And i Find the perfect one again on Aliexpress

search for:IMG_2392.thumb.JPG.21d8a83675800d67e8a9bd41aebdf543.JPG 320Mm 400N Flap Spring Flap Fitting Gas Spring !

they match perfectly.

The Trunk lid will hold until 15cm before reaching the lock.

 

  • 2 months later...
  • 3 weeks later...
sleptema Proficient

sleptema

Posted
  • Author
Posted
On 13/08/2019 at 1:21 PM, rych said:

I hate to necro this but when you use a 10mm spaner to wedge the strut out did you had to drill a hole to make new strut fit? 

Nah, the strut guy just got a fitting on the new strut that fit over the 10mm ball joint.

  • 1 year later...
R33 Jared Enthusiast

R33 Jared

Posted
Posted
On 20/05/2019 at 8:47 PM, Fastlane said:And i Find the perfect one again on Aliexpress

search for:IMG_2392.thumb.JPG.21d8a83675800d67e8a9bd41aebdf543.JPG 320Mm 400N Flap Spring Flap Fitting Gas Spring !

they match perfectly.

The Trunk lid will hold until 15cm before reaching the lock.

 

Hopefully this is still correct years later because I’ve just purchased some. Cheers mate

  • 3 months later...
Rusty Nuts Experienced

Rusty Nuts

Posted
Posted
14 hours ago, joshuaho96 said:

I need a replacement for the trunk gas strut

https://www.ebay.com.au/itm/AUTOPA-Gas-Bonnet-Strut-for-Mercedes-W221-C216-S350-S450-S500-S63-A2218800329/254807343124?hash=item3b53b38014:g:5fMAAOSwBYteZbCj&frcectupt=true

here's the link on ebay for the struts, in stock in Sydney.

If you need any strange brackets or ends. Here's the link to a strange brackets or ends seller also local.

https://www.gasstrutaustralia.com.au/

joshuaho96 Veteran

joshuaho96

Posted
Posted
4 minutes ago, Rusty Nuts said:

https://www.ebay.com.au/itm/AUTOPA-Gas-Bonnet-Strut-for-Mercedes-W221-C216-S350-S450-S500-S63-A2218800329/254807343124?hash=item3b53b38014:g:5fMAAOSwBYteZbCj&frcectupt=true

here's the link on ebay for the struts, in stock in Sydney.

If you need any strange brackets or ends. Here's the link to a strange brackets or ends seller also local.

https://www.gasstrutaustralia.com.au/

I'm in the US, my concern is that the gas strut is too strong. The Alibaba generic one is said to be more appropriate, so I'm thinking of trying one of those first.

  • 2 weeks later...
BK Grand Master

BK

Posted
Posted
On 23/01/2021 at 3:09 PM, IM-32-FK said:

Don’t get replacement ones, you can get the OEM ones regassed. There’s a couple of places in Sydney that I know who do it.

Only if the seals are good. If they're not, which they probably aren't, they're a throw away. Just retain the top boot lid mounts to adapt to new ones.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • PLYNX
      Short shifter r34

      By PLYNX · Posted

      Don't do it if your gearbox box has already having syncro issues. The short hifter will put a greater load on them. If you must I remember Nismo did a shorter shifter, with the top part being physically shorter and the part that went into the gearbox was the same as stock. In saying that I've had a C's short shifter (I think) in mine for many years, which was given to me as the previous owner was not sympathetic to the gearbox. Thus forwarned I was careful and had to modify my normal changing style. You have to be super accurate with your clutch and shifts
    • CRSKmD
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By CRSKmD · Posted

      Well, after a week of daily driving and having to crawl out between the wheel and the side intrusion bars. I got myself a quick release setup. I went with an NRG short hub and Quick Release with some cute heart cutouts on the pull tabs. Nice and matchy matchy with the rest of the interior accents I have going on.  The only downside is the total stack height even with the short adapter is longer than the old HKB boss kit. Luckily I had some adjustment left on the column so move the wheel away.
    • robbo_rb180
      Short shifter r34

      By robbo_rb180 · Posted

      stock shifter with new bushes, springs and cup will improve it. Gktech do all the bits. The opinion as the years have gone on is the redline is not great in old gearboxes.
    • drifter17a
      Short shifter r34

      By drifter17a · Posted

      Hi all   what short shifter do you use on your skykine r34?   my synchronous does have a problem and i was getting huge delay and grinding sound between 2nd and 3rd, did put shockproof red heavy stuff and it is great now/ no issues   would in your view short shifter screw this up?   people seems to suggest/ use cube short shifter and there is standard and premium. Seen review of premium as much better and less play. Thoughts?
    • GTSBoy
      R34 oil and timing belt change

      By GTSBoy · Posted

      Yeah, there's a bit of a density and friability difference between pebbles and any of those other things. Silicone will definitely float in oil and so will be mobile enough to move around. Although, again, if it is upstream of the filter it really shouldn't go any further. I would only ever worry about silicone when it is in places downstream of the filter. Upstream of the pickup is a whole 'nother matter. We've all seen what that does. I have seen the most abominable crap settled out in industrial gearboxes, trunnion lube systems and the like, without any sign that any of it has touched anything in the machine. Just chilling in the bottom, waiting for the inevitable operator error that causes the whole machine to need to be dismantled for repairs.
×
×
  • Create New...