Jump to content
SAU Community

Xtreame tripple plate clutch

Taha
 Share

Recommended Posts

  • 3 weeks later...
BK Grand Master

BK

Posted
Posted (edited)

Nismo twin plate got nothing on ATS. Not even same ballpark to an ATS carbon twin, let alone a triple. I Don't think Xtreme / Xclutch sell them anymore as they were repackaged ATS. Go to the Jap site

Edited by BK
More info
Link to comment
Share on other sites
BK Grand Master

BK

Posted
Posted

Yeah the Xclutch ceramic twin or Nismo twin will hold for a while, maybe even a full season or two with 500+Kw.Then the clutch will warp the metallic floating discs from heat, probably before the ceramic plates wear out and won't be able to get it into gear. It's all pretty relative to how the car is launched to how long they last. Another 32 here made it 3 seasons at 350rwKw with a Nismo twin before it cried enough for example.

Decent power car above, about what my R32 was on the 2.6 before Nitto 2.8. Crap 60ft and crap ET for140mph though. Mid 10's is do-able at 130mph. Should be well into the 9's with that MPH. Not to mention 500rwKw won't last long on stock bottom end.

The point I was making with the carbon ATS triples is they last nearly forever compared to everything else, which might hold the power but will wear out quicker. One season I spent 30k on clutches and gearboxes before the ATS.

Never looked back. Got one in my 330rwKw 33 and I don't think that car will EVER need a clutch ever again after looking at how it has performed in my 32. Good luck with everything.

Link to comment
Share on other sites
WantGTR Mentor

WantGTR

Posted
Posted
On 7/25/2018 at 9:50 AM, niZmO_Man said:

Nah. Buy Nismo twin plate.

Average AF clutch bro lol.

I make a bit over 500kw atw and installed a new nismo twin plate c spec with flywheel. Doesnt slip but i reckon its at its limit.

Link to comment
Share on other sites
BK Grand Master

BK

Posted
Posted

10.6 @ 127mph - it's in my bottom signature. Was really laggy on 2.6 but managed 1.5 - 1.6 60ft with Mickey Thompson 255 ET street radials. Still running in Nitto 2.8 engine as we speak, so haven't run it yet. Haven't done the full power tune yet either. Red centre nats 4 is on the 1st and 2nd of September so I'll be on the dyno there with a figure to report. Once everything is tuned correctly I'll hit the strip after that. Hopefully 9's too but it'll run what it runs

Link to comment
Share on other sites
BK Grand Master

BK

Posted
Posted
41 minutes ago, Taha said:

Going 30 when it blows  I done 1.52 2nd launch  snapped  cv and night was all over would of been a high 9    be back next week

Snapped CV, wow. Yeah I was looking at the US driveshaft shop CVs in case that happens - $3k +

Just out of interest, what box are you running ? I was running a Trust / Quaife 6 speed dog until I broke it after about 2 years. Back to OS giken sychro for the moment. Maybe PPG next year.

Link to comment
Share on other sites
  • 3 weeks later...
BK Grand Master

BK

Posted
Posted

That is crazy ! Well done ! I destroyed 3rd gear in my 32 stock box the first time I ever ran MT ET streets. Broke Trust / Quaife 6 speed straight cut dog box 3rd after about 40 - 50 mid 10 passes. Got a 5 speed Giken at the moment but I think it's PPG time...

Link to comment
Share on other sites
BK Grand Master

BK

Posted
Posted

Never had an issue but others have broken them. Thinking of selling it as I want to go back to a dog box so badly. Pity PPG is so $$$ for the fully optioned 5 speed straight cut set, like $13k for a gearset. $10k without mainshaft and assembly. Don't know if I can justify that.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • 180 wanabe
      Thinking of getting a Q50 300hp and just tuning it instead of getting the Q50 Red or 400R

      By 180 wanabe · Posted

      So next year I am looking at upgrading from my VE SS bomadore ute to something more refined.  I wanted to stick with a V8 but not anything German or Australian, either a coupe or a sedan. So if I wanted anything newish that limited my options to either the Lexus RCF which I quite like. But with the price they demand and a kid on the way a 2 door coupe is probably not going to be the best idea. The next best thing would be the ISF but the newest models are 2014 and commanding over 60k and even the older 2008 models in ok condition starting around 35k is kind of bullshit. So I figured if I could not have the noise I could perhaps make do with easy power. Enter the infinity Q50 or Skyline equivalent. The price difference between the 300 and 400hp models seems a bit crazy. Right now there is 300hp Q50 one on carsales from a dealer with 61km for 27k drive away. If I wanted to get a 400hp Red or 400R car the prices seem to start at 43k From my limited research it seems that the only differences are that the 400r/Red Red runs more boost and a more aggressive tune. There are are turbine speed sensors on the turbos. Has 2 pumps for the water to air intercooler. Runs an engine oil cooler. I'm guessing that the exterior trims might look a little more sporty as well. I had a lazy look for upgrades to bridge the gap on z1motorsports They have kits that upgrade the water to air heat exchanger as well as the coolant pump which should give a non Red/400r better intercooling temps than the stock Red/400r. I added an engine oil cooler with a thermostat as well to try and make things as close as possible. Obviously the ECU is going to need a tickle. Having not done much in the way of research they also sell a ECU flashing tool with pre loaded tunes that are supposed to boost the non Red/400R by 100hp which adds 1k USD to the cost. The total cost of the parts @ the current time including shipping and taxes worked out to be $4350 AUD. Personally I would rather get the car tuned on a dyno which would probably add more cost Assuming the worst that you got a workshop to install the new parts I would guess no more than 5 hours would be required in the worst case @ 5 x $150 per hour = $750 So the total cost could be around $5100 So for easy number 5k + 27K = 32k I guess that would leave some change left over to swap out the open diff and fit a LSD Any thoughts?      
    • joshuaho96
      Blow Off Valve Is Causing Car To Stall!

      By joshuaho96 · Posted

      Right, not sure why I thought it to be a lean spike. It might be fixable with modern card-style hot film MAFs which have some design features to avoid counting reversion flow but I've never tried it myself.
    • Leigh_Mack
      Hello, Newbie, anyone know my 32's history?

      By Leigh_Mack · Posted

      I did not realise this, I'll contribute more and earn my stripes and retry later. 
    • GTSBoy
      Hello, Newbie, anyone know my 32's history?

      By GTSBoy · Posted

      I'm only going to hassle you for posting links to images. It's against my policy to click links that could be some nasty payload. Sadly, you need to make 9 more posts before you can just stick the images directly in a post, unless @PranK sees this and bends the rule for you.
    • Leigh_Mack
      Hello, Newbie, anyone know my 32's history?

      By Leigh_Mack · Posted

      Hello,new to the group, I bought a R32 from auction recently, wondering if anyone knows the cars history, seems to have the usual go fast bits on it, plan is to do an engine swap- add 2 extra cylinders and 1 extra turbo. https://www.dropbox.com/scl/fi/i4rjmlzubjbwjtguh6f4s/IMG20241011140744.jpg?rlkey=q0lumm251377vknbqktfwrycq&st=7scvwx4e&dl=0 https://www.dropbox.com/scl/fi/ro24qmwzlczzlfsr4y05x/Screenshot_2024-10-10-10-49-23-90_9a2f5bb2149dae94cd1e190effc09b33.jpg?rlkey=oyguh26ttshlf04ccp48odf4v&st=xloae97b&dl=0   New to forums and posting pics, if links don't work, take it easy on me, 42yrs old and I tune carburettors!!  
×
×
  • Create New...