Jump to content
SAU Community

My Rb25/30 turbo choice

Rb25/30nissan

By Rb25/30nissan,
in Engines & Forced Induction

 Share

Recommended Posts

Rb25/30nissan Rookie

Rb25/30nissan

Posted
Posted

Hi Im currently building a rb25/30 and pretty much at the stage where I need to think hard about turbo choice The botton end is forged spool rods, cps,.. Id like a fast street car but a daily aswell looking for 400hp maybe abit more but want to stay on pump fuel Will the gt3582r turbo be a good choice cheers for any professional info.

Link to comment
https://www.sau.com.au/forums/topic/474812-my-rb2530-turbo-choice/
Share on other sites
KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted
On 8/29/2018 at 3:40 AM, Rb25/30nissan said:

Hi Im currently building a rb25/30 and pretty much at the stage where I need to think hard about turbo choice The botton end is forged spool rods, cps,.. Id like a fast street car but a daily aswell looking for 400hp maybe abit more but want to stay on pump fuel Will the gt3582r turbo be a good choice cheers for any professional info.

I put a 3582R on my RB30 Stagea but used .63 rear for max take off (heavy wagon) but would have preferred a .82 for a little more grunt on the track. Today I would use a modern turbo. Unusually a Wellington workshop did a back to back comparison on the same car (Skyline with RB30) and got the following results:

.63 rear at 18 psi = 350kw

.82 rear at 18 psi 375kw

I would suggest the .82 for you as it would be easy to get 400kw out of it and for a street car would drive better than with a 1.00 rear.

PS just noticed you only want 400hp not kw. You will do that with a GT3076 easily.

KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted
1 hour ago, Rb25/30nissan said:

Thanks for the reply and your comments. What rev range will the gt3582r start spooling

This is with the .63 rear on my car -with VCT, Link ECU, mac valve, 50mm Synapse wastegate, Sinco manifold :

 

2013.11.21 Boost curve 001.jpg

Looney_Head Rising Star

Looney_Head

Posted
Posted
14 minutes ago, Pelefoti said:
On 9/7/2018 at 2:08 PM, Looney_Head said:
i have a borg warner s300sx with a .91 twin scroll housing on my rb25/30, and am getting a bar at 3700ish rpm, it makes 500hp on 14psi on pump gas.
 
and cost less than 1k NZD landed

What website was that

http://www.theboostlab.com/s300sx3-60-91-a-r-straight-compressor-outlet/

this is the turbo i got, the exchange rate was good at the time

Dale FZ1 Veteran

Dale FZ1

Posted
Posted
On ‎9‎/‎11‎/‎2018 at 9:29 AM, Looney_Head said:

a 8375 s360

Did the physical bulk of this unit cause much packaging/fitment issues?

What manifold?  Pics would probably tell a lot for people contemplating the same unit.

Looney_Head Rising Star

Looney_Head

Posted
Posted (edited)

Nah it's not too bad, I am running a sinco twin scroll manifold for a rb30, they make the collector lower for the 30.

A walk around of my setup.

 

i tried to add a pic, but for some reason its not loading :/

 

 

Edited by Looney_Head
  • Like 2

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • DRoc81
      Shifting questions

      By DRoc81 · Posted

      Interesting.  Great info. thank you.  Give a few days to get that name plate.  I have a busy life most weeks.  I will be in touch.
    • Murray_Calavera
      MAJOR FUEL ISSUES 25det neo r32

      By Murray_Calavera · Posted

      Strange your posting about this being an issue. Move the harness or change your wheels or run more camber etc. Have the thing not touch the thing so it doesn't destroy the thing.  Short answer, no. Slightly longer answer, the factory fuel gauge is measuring resistance. You need to wire in the FPG fuel level sender into the original factory fuel level sender wiring.  I drew you a picture to explain this one The factory strainer is quite long, reaching down into the bottom of the tank. Safe bet your aftermarket fuel pump has a little baby sized strainer that probably doesn't even point down towards the bottom of the thank.  Solution, move the pump lower down in the tank, or fit a longer strainer, or do both. I did both, I've run my tank down to 5L remaining and the car still drove fine.   
    • Dose Pipe Sutututu
      Is r33 gtr steering wheel the same as the gtst?

      By Dose Pipe Sutututu · Posted

      S2/3 GT-R is the same as S2 GTS-t The SRS airbags module in under the centre console. The S1/S1.5 GTS-t and S1 GT-R had the module built into the steering wheel. FWIW, I have a S3 GT-R wheel in my S2 GTS-t shit box. Same airbag plug, airbag light goes on then off, meaning all systems are go. S3 GT-R has red stitching, that's about it.
    • PotatoCake
      Is r33 gtr steering wheel the same as the gtst?

      By PotatoCake · Posted

      Dumb question, but why would it matter if the wheel came off a car with hicas or not?
    • 25debt
      MAJOR FUEL ISSUES 25det neo r32

      By 25debt · Posted

      Hey to anyone that reads this, long time lurker first time posting, sorry if it’s been answered before but I’ve been looking for nearly a year now for answers. ive got a 25det neo in an r32 that works awesome when it works (made 500whp on 21psi) but works 45% of the time, 1st issue there’s a harness that runs under the passengers side front fender that my tire keeps rubbing through and one wire seems to power the fuel pump even though I’ve done the relay “mod” some people like to call it, and when it does rub through it kills the car, yes next time I’m with the car I want to take the fender off and try tuck the harness well out of the way but I’d also like to try and by pass this mysterious wire as well lol, also wouldn’t mind getting power from the alternator as I’ve read it supplies the pump with 13v ? But no idea where to run the power wire too. 2nd issue, when replacing my fuel pump and fuel hanger I managed to break the factory fuel level sender leaving me with no fuel gauge, I’d like to buy the fpg fuel level sender for r32/s13 but the plug it comes with confuses me, I’ve got a detschwerks x1 fuel hanger which has light + pump - level + pump + and a ground, I’m no auto sparky but I’m wondering if I can cut the plug off the fuel level sender and wire the negative to the pump negative and wire the positive to the level positive to get a fuel gauge back ?🥴 3rd and final issue, the reason I want a fuel gauge is because whenever it’s below half a tank, it fuel starves like crazy and runs like a bag of shit even without doing a pull or sloshing the fuel round in the tank, I’d also like to fix this but have no idea what’s causing it, I’ve got a dw420 and a dead head fuel setup meaning the fuel is regulated before it gets to the engine, my only theory is that the return line is to close to the pickup on the pump and when it’s at half a tank the return line is causing the pump to cavitate enough to cause fuel pressure issues, that or the pump isn’t low enough in the tank which I would find strange considering I can’t find a single thing online about it, also if ya wondering how I figured out it happens at half a tank without a fuel gauge, I waited until it started happening and went and filled up and the car took exactly 30 litres every time I tested it, if ya managed to read through this mess I appreciate that and any recommendations , cheers
×
×
  • Create New...