Jump to content
SAU Community

Precision 6266,Trust T78-29D,NPC push clutch,BPP fuel rail,32 N1 bootlips,Turbosmart FPR800 fuel reg,R32/R33 GTR blow off valves,GTR front diff centre,1000cc injectors


Recommended Posts

  • 2 weeks later...
  • 2 weeks later...
  • 3 weeks later...

31 tooth rear gtr half shafts - SOLD

Added for sale:

Used HKS EVC III boost controller complete - $250

Used HKS EVC IV boost controller complete - $290

Used Trust oil cooler 13 row core with AN10 tank fittings - $220

Brand new 40psi electronic 60mm JDM dual analogue / digital 40psi display boost gauge with MAP sensor and mounting cup - $220

If anyone needs a 10 clutch transfer case upgrade ($1200 including parts) or OS giken gearset build ($1400 labour only. Can supply all parts if needed.) can do as well. 2 - 3 month lead time. Shipping to and from obviously extra.

Link to comment
Share on other sites

  • 4 weeks later...

Nitto billet 2.8 crankshaft - SOLD AND GONE !

Oil cooler sold pending payment, read again, PENDING PAYMENT ! Still for sale until that.

I will get turbo and 1000cc Denso / Sard injector pics up soon.

Also have NEW 6 x Bosch full length injector adapters for sale 11mm rail  - $80 posted

60mm boost gauge with remote mount MAP sensor 1.6BAR. Remote mount peak / hold setting controller. Boost gauge without pressure in cabin ! Comes with 60mm gauge cup too ! - $110

Link to comment
Share on other sites

New photos !

NEW R34 GTR lower shifter bushes - $10

100mm turbo bell mouth. Anodised blue - $80

HKS EVC III boost controller complete with instructions. Max 2 bar boost. - $270

HKS EVC IV boost controller complete with instructions. Max 2.5 bar boost. - $290

6 x 1000cc low impedance 1000cc Denso / Sard injectors. 0.85ms lag. Denso high guide plug type. - $700 FIRM

1.6 bar electronic boost gauge with 60mm mount cup and peak / hold controller. No boost lines into cabin. - $110

NEW 6 x Golebys 11mm Bosch injector adaptors with o rings. Full length.  - $70

HKS T51S 1.00 A/R turbo pics tomorrow. - $1500 ono

WP_20190316_14_17_40_Pro.jpg

WP_20190621_14_44_17_Pro.jpg

WP_20190621_14_44_29_Pro.jpg

WP_20190621_14_44_54_Pro.jpg

WP_20190706_23_09_31_Pro - Copy.jpg

WP_20190706_23_09_31_Pro.jpg

WP_20190706_23_09_47_Pro.jpg

WP_20190706_23_10_14_Pro.jpg

WP_20190706_23_10_54_Pro.jpg

WP_20190706_23_11_08_Pro.jpg

WP_20190706_23_11_41_Pro.jpg

WP_20190706_23_12_00_Pro.jpg

WP_20190706_23_12_19_Pro.jpg

WP_20190706_23_13_08_Pro.jpg

WP_20190706_23_13_23_Pro.jpg

Link to comment
Share on other sites

  • 4 weeks later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share




  • Latest Posts

    • Not easy to find pics from 15 years ago, but here is a partial one. Keep in mind that it curved immediately from the airbox, then kept a straight line for the MAF to read correctly, followed by a 45 degree bend straight down to the turbo. This connection was the most difficult as it had to twist as well as bend to meet the almost vertical straight section of the intake.
    • Yes, well, wrt a wheel alignment, there are two types. Either: You have very little added adjustables, in which case the alignment can be done by anyone in any tyre shop or equivalent, and will only take 30 minutes, and so there is no reason to even consider leaving the car there. OR: The alignment is a major exercise because you have adjustables everywhere and so you will need to be taking it to a shop that is skilled and experienced at setting up race cars and the like, and you won't need to worry about leaving the car there.
    • does anyone know the specs of the R35 master cylinder, rear ratio and knee point? the BM57 is a 0.4 rear ratio with a 435psi knee. I'm looking for someone with a much lower knee pressure. the piston area of the R35 brakes isnt that big so might not work for me but this is interesting.. the other option for me is a GU patrol master cylinder and booster and do the prop valve externally.
    • It sounds like by avoiding maintenance you may be doing more damage than a hypothetical guy in a workshop taking it for a spin. Not sure if you are just being paranoid or things are actually that bad in the US. Find a reputable shop not run by dickheads. Look for people that take pride in their work. Stick around for the day if you have to
×
×
  • Create New...