Jump to content
SAU Community

Help! R34 gtt manual converted running rough

TaylorS

By TaylorS,
in General Maintenance

 Share

Recommended Posts

TaylorS Contributor

TaylorS

Posted
Posted

Hey everyone. I just got a manual conversion done on my 1998 r34 gtt and now it is running funny. It revs very slow and goes slower then my na r34 now. It is still running the auto ecu. Im thinking that might be the problem? Or maybe the coils? Please anyone that has had this kind of problem let me know.

Ps. Sorry if this is in the wrong part of the forums 

GTSBoy Grand Master

GTSBoy

Posted
Posted

Auto ECU will not be the problem.  The only difference between auto and manual ECUs (apart from slight differences in mapping) are that the auto ECU also contains the TCU.  Oh, and the idle ignition timing is 20° in autos, not 15° like in manuals.

There could be the usual million explanations.  From coils, to dirty AFM or faulty wiring.  Perhaps you need to do a diagnostic on the ECU and looks for codes.

  • Thanks 1
TaylorS Contributor

TaylorS

Posted
  • Author
Posted (edited)
1 hour ago, GTSBoy said:

Auto ECU will not be the problem.  The only difference between auto and manual ECUs (apart from slight differences in mapping) are that the auto ECU also contains the TCU.  Oh, and the idle ignition timing is 20° in autos, not 15° like in manuals.

There could be the usual million explanations.  From coils, to dirty AFM or faulty wiring.  Perhaps you need to do a diagnostic on the ECU and looks for codes.

Ok thanks mate i will give the diagnostic tool ago and see what it finds when i get home. The car seemed to run fine before it was converted. If the car was running fine before could it still be the coils? 

Also the car has no aftermarket mods except a hks catback

Edited by TaylorS
GTSBoy Grand Master

GTSBoy

Posted
Posted

The logical source of problems would be wiring that was f**ked up during the conversion.  The driver's side engine bay loom that services the plugs on the transmission is an example of a place that you need to make changes.

Coils much less likely to die except by pure coincidence.  AFM wiring, oxy sensor, knock sensors are all more likely to be abused during work in the engine bay.

  • Thanks 1
TaylorS Contributor

TaylorS

Posted
  • Author
Posted
10 minutes ago, GTSBoy said:

The logical source of problems would be wiring that was f**ked up during the conversion.  The driver's side engine bay loom that services the plugs on the transmission is an example of a place that you need to make changes.

Coils much less likely to die except by pure coincidence.  AFM wiring, oxy sensor, knock sensors are all more likely to be abused during work in the engine bay.

Ok thanks for the tip mate. It wasn't me who did the conversion, i got it done from a shop so i really hope its not the wiring because i wouldn't know what to do then because the shop isnt sure why its like that either.

I will charge the coils anyway and will put some spitfires in. 

I should also add that at random points in the higher rpm it seems to kick in and then drops back out again.

Sorry for all the questions and stuff

Robocop2310 Experienced

Robocop2310

Posted
Posted
3 minutes ago, TaylorS said:

Thanks for the tips mate, i will check that out too 

All good mate.

Also as some have suggested plug in a cable and run some diagnostics if possible.

Could also be the exhaust too check piping.

  • Thanks 1
Robocop2310 Experienced

Robocop2310

Posted
Posted
4 hours ago, TaylorS said:

Ok definitely will try that tomorrow. Do you think it could be a boost leak causing all this?

Yes definitely a possibility but jack the car up and check exhaust piping ang turbo gasket first followed by hoses and blow off valve leakage.

  • Thanks 1
DatsunBanana Enthusiast

DatsunBanana

Posted
Posted

Couple of times I've had the circlip on the turbo actuator arm fall off and the actuator disconnect. First time it was on a CA18DET and ran absolutely gutless. It's also happened on my RB25DE (with turbo conversion) but wasn't as bad cos the compression is higher so just felt like it was running non-turbo again.

  • Thanks 1
TaylorS Contributor

TaylorS

Posted
  • Author
Posted
12 minutes ago, DatsunBanana said:

Couple of times I've had the circlip on the turbo actuator arm fall off and the actuator disconnect. First time it was on a CA18DET and ran absolutely gutless. It's also happened on my RB25DE (with turbo conversion) but wasn't as bad cos the compression is higher so just felt like it was running non-turbo again.

Thank you for that, i will check that out as well. It could be anything at thid point haha. It does run guttless so it could be that

TaylorS Contributor

TaylorS

Posted
  • Author
Posted

Update: hey everyone i was playing around with the car and i think i have narrowed the problem down to a turbo issue. it seems like i am getting no boost. the boost gauge reads all the way up the top of the gauge at max and i can hear the turbo spalling  but it feels like im getting none of it?
does anyone know what could be wrong from that kind of an issue? is the bov broken?

thank you

  • 2 weeks later...
TaylorS Contributor

TaylorS

Posted
  • Author
Posted

hey everyone i have a few updates.
To begin with i totally forgot to mention that the A/T light has been since the conversion. is this normal? 
i also checked for error codes and it came up with error 34 which is knock sensors. does this have to do with the A/T light?
thank you in advance  

iruvyouskyrine Grand Master

iruvyouskyrine

Posted
Posted

knock sensors have nothing to do with the AT light.

If you arent making any boost but your turbo is still making all the woosh sounds them im going to say you have a massive air leak or there is a rag in your intercooler piping.

  • Thanks 1
TaylorS Contributor

TaylorS

Posted
  • Author
Posted
1 hour ago, iruvyouskyrine said:

knock sensors have nothing to do with the AT light.

If you arent making any boost but your turbo is still making all the woosh sounds them im going to say you have a massive air leak or there is a rag in your intercooler piping.

Ok thank you mate, i didnt think the knock sensors have anything to do with the AT light. 

Yes your right the turbo is still making all of its noises but it doesnt want to boost.  I will have to check out the intercooler next.

Also can the knock sensors casue the car to get no boost? Maybe trigger a safe mode or something?

Robocop2310 Experienced

Robocop2310

Posted
Posted
6 hours ago, TaylorS said:

Ok thank you mate, i didnt think the knock sensors have anything to do with the AT light. 

Yes your right the turbo is still making all of its noises but it doesnt want to boost.  I will have to check out the intercooler next.

Also can the knock sensors casue the car to get no boost? Maybe trigger a safe mode or something?

Whilst you’re get it check your AFM and wiring/tubing to your air intake and intercooler.

  • Thanks 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      MLR's Bogan cruise ship

      By MBS206 · Posted

      Nah, I'm not an a-hole, ha ha!   I do like the colour match. Some of the carbon fibre wraps are quite freaking horrible. There's one a local company I know uses, and it looks damn good! Also very very expensive per metre to buy! ha ha ha It might be cheaper to respray the roof than use the good CF Wrap, ha ha!
    • The Bogan
      MLR's Bogan cruise ship

      By The Bogan · Posted

      Please noooooooo 😭 As for wrap, no thank you mate, I've seen and used "carbon fibre" wrap before, and for these hard tops, they look soooo good when colour matched Like this >>>
    • MBS206
      MLR's Bogan cruise ship

      By MBS206 · Posted

      That depends, someone might offer me a good price to resell it Mark... Ha ha ha!   I can get it wrapped in a really nice looking carbon fiber vynil if you want?
    • The Bogan
      MLR's Bogan cruise ship

      By The Bogan · Posted

      I ❤️ Matty I would like to thank Matty for going out his way in securing me a OEM NC detachable hard top for the NC Matty, your worth your weight in gold, and I cannot say how much I really appreciate your outstanding help I'll get it colour matched once I pick it up sometime in Dec-Jan 😁  
    • Rezz
      OEM Soko: Japanese business supplying Automotive items from Japan - Freebie inside!

      By Rezz · Posted

      We have some genuine Japanese legally decommissioned car number plates now in stock 🙂 Add some legitimately obtained JDM style to your Skyline or other Japanese model, or simply as a garage/man cave decoration! About the 40mm hole: The Ministry of Land, Infrastructure & Transport in Japan recognised the popularity of keeping decommissioned plates among car enthusiasts and came up with a method to "destroy" (or render them unusable for street use) while still retaining their collectable/usable value for display etc.  We have 40mm hole covers available to cover the hole nicely with a Sakura motif, which are also available in white in (very!) limited quantities, however they frequently sell out. Please let me know if you're wanting one or more of these and I'll check availability. The Sakura motif covers are more common. https://www.oemsoko.co.jp/products/genuine-decommissioned-japanese-vehicle-number-plate-set-su-7515 https://www.oemsoko.co.jp/products/genuine-decommissioned-japanese-vehicle-number-plate-set https://www.oemsoko.co.jp/products/genuine-japanese-vehicle-number-plate-400mm-hole-cover *Please note that we can't obtain particular number or area name (eg: "Gunma 500 Fu ・86") if requested. All plates are provided as they become available after decommissioning. 
×
×
  • Create New...