Jump to content
SAU Community

R34 GTT idle problem

Danowner
 Share

Recommended Posts

Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted
4 hours ago, silviaz said:

Apexi, though I'm not comfortable with setting the idle, knowing me I'll f**k it up lol.

Ohh even easier.

 

Go dial up 700rpm on the hand controller. Rip off the TPS plug, wait till the idle drops and then adjust the IACV screw so it's just a tad below the target on the hand controller (say 650rpm), plug the TPS back in and idle will climb back to target.

Done.

silviaz Proficient

silviaz

Posted
Posted (edited)
2 hours ago, Dose Pipe Sutututu said:

Ohh even easier.

 

Go dial up 700rpm on the hand controller. Rip off the TPS plug, wait till the idle drops and then adjust the IACV screw so it's just a tad below the target on the hand controller (say 650rpm), plug the TPS back in and idle will climb back to target.

Done.

That sounds pretty easy actually haha. But is there a reason why the tuner didn't do this? It's not like I've got a cammed 500kw rb25 neo. 

 

Also the tps plug is different on the rb25det neo and the r33 for example, I guess I'd plug out the loom which is this end? There's also 2 connectors. 

image.png

Edited by silviaz
Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted
6 minutes ago, silviaz said:

Also the tps plug is different on the rb25det neo and the r33 for example, I guess I'd plug out the loom which is this end? There's also 2 connectors. 

Unplug both, it causes the idle closed loop condition to not be satisfied 

soviet_merlin Experienced

soviet_merlin

Posted
Posted
9 minutes ago, Dose Pipe Sutututu said:

A high case of cbf.

Car runs, idles fine, not touching it.

I mean, what's the concern here? Higher fuel consumption?

FWIW my idle sits at around 800rpm or so as well. And yes, it runs fine, idles fine and there are no issues as far as I can tell. I don't quite see the problem.

  • Like 1
silviaz Proficient

silviaz

Posted
Posted (edited)
26 minutes ago, soviet_merlin said:

I mean, what's the concern here? Higher fuel consumption?

FWIW my idle sits at around 800rpm or so as well. And yes, it runs fine, idles fine and there are no issues as far as I can tell. I don't quite see the problem.

I know it's probably not going to cause any major engine issues. I just had a more generic concern that it's technically not running right (I guess this means the rpm is not sitting where it technically should be) Though the other thing is, it's that my steering wheel is shaking at 1,100 rpm at idle until it gets warm (seemed to happen after I tightened my alternator belt, will be testing the alternator soon).

Edited by silviaz
joshuaho96 Veteran

joshuaho96

Posted
Posted
53 minutes ago, soviet_merlin said:

I mean, what's the concern here? Higher fuel consumption?

FWIW my idle sits at around 800rpm or so as well. And yes, it runs fine, idles fine and there are no issues as far as I can tell. I don't quite see the problem.

For me at least the reason why it bothers me is because it's indicative of a deeper problem. And that will nag at me forever. Especially because I have tailpipe emissions testing + evap leak testing every 2 years.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      OK, solid mount Z1 diff brace is in, pretty straightforward, it picks up 3 diff hat bolts and ties them to 2 support bolts on the subframe. Pretty sure someone else on here said they had reduced axle tramp with this but mine was already pretty good for smooth wheelspin, and still is....will see you this goes over time and whether I end up with a broken rear diff hat
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Ah yes, but the part in my hand was actually painted and fitted by me! I knew any front lip was likely to be sacrificial but I've had to fix it twice already... by the time I buy a fibreglass fixing kit, sort out sandpaper blocks, buy some fibreglass filler, body bog, spend the time and effort for a 'Greg' result... a new one being $290 seems like it's the better way to go and spray that with bedliner/raptor coat and we're all pretty again.. Would have preferred it last more than a month though. Them's the breaks I suppose.
    • MBS206
      HKS stroker kit step 0/1 or HKS GTIII 2530

      By MBS206 · Posted

      I find it funny that the USA is finding out all this really really weird stuff, and people from the USA are coming here treating it like gospel, yet, all the info on solving those issues is here on these forums for the last 15 odd years... Also, I know how much heat it takes to ignite the hood lining of an R33 skyline. I worked it out myself... It also took a LOT of time, and heat for it to do it... Big single, and I needed to drive the car, so retarded the timing off to "protect it". Yeah, that was a bad move for cruising on a freeway with only 15 degrees of timing on it. That was a lesson I learned around 2009. So that's over 15 odd years ago. Aligning water and oil, that's identical for any turbo engine, it's not Japanese specific. If a shop doesn't know how to make sure the core is rotated the right way, then they shouldn't be touching any turbo engine. That's not a matter of "We haven't had Skylines for that long here"...
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Sounds like it is rotational in the driveline. CV? Tailshaft CB? Also.....didn't you just pay to have that bit painted and put on the car?
    • GTSBoy
      R34 GTT idle problem

      By GTSBoy · Posted

      Yeah, when I dialled my idle down, given how much time I spent idling at the lights in traffic on my daily commute, the effect on overall fuel consumption was absolutely noticeable.
×
×
  • Create New...