Jump to content
SAU Community

Tune Question

Missileman

By Missileman,
in Engines & Forced Induction

 Share

Recommended Posts

Missileman Veteran

Missileman

Posted
Posted

As the weather is warming up I've noticed that my 32gtst is not starting from cold as easily as it does or should compared to winter time, we just had a really cool morning and the car started first crank, when the engine is at operating temp restarting is fine, always first crank, it just has an issues starting first start of the day when ambient temps are over 25c

Any suggestions before I start playing around in nistune?

Link to comment
https://www.sau.com.au/forums/topic/475135-tune-question/
Share on other sites
Missileman Veteran

Missileman

Posted
  • Author
Posted
On 10/12/2018 at 9:21 PM, burn4005 said:

Probably need more crank prime at warmer areas

After looking at the tables I think you are correct, I've added a couple of percentage in the 20c and 30c blocks of the cold crank enrichment table., have to wait until the ambient tenps warm up to see if it made any difference.

Link to comment
https://www.sau.com.au/forums/topic/475135-tune-question/#findComment-7887810
Share on other sites
  • 1 month later...
Missileman Veteran

Missileman

Posted
  • Author
Posted
On 10/15/2018 at 10:45 AM, Missileman said:

After looking at the tables I think you are correct, I've added a couple of percentage in the 20c and 30c blocks of the cold crank enrichment table., have to wait until the ambient tenps warm up to see if it made any difference.

Update: my correction to cold crank enrichment has worked... starts like and idles like a champ once again.

So now I suppose I should start looking for any air leaks, but only when all the rubber is cold.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/475135-tune-question/#findComment-7893068
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      There are a few different ways of doing it. I'm currently running two 1000cc pre-TB nozzles and PWM the pump for control. I'll be moving over to a constant pressure system and direct port. I'll run the pump off a regular relay, have it cycle on roughly 5psi before I start injecting to build pressure and then PWM a WMI solenoid (It's basically an injector that can take a lot of pressure and not corrode with water and meth.) The solenoid feeds the 6 direct port ~200cc nozzles. I'll also keep one ~250cc pre-TB nozzle to help keep IAT's in check.  Safety will be a little different as well. I used to use a pressure switch but will be moving over to a pressure sensor between my solenoid and nozzles. I'll trigger my solenoid and if I don't see specific pressure within a specific timeframe (e.g 100psi within a second, 175psi within 2 seconds), I kill it and revert back to non WMI maps the same way I did it before with 4D in Haltech. I was just figuring out the timers in my ecu last night. They made that a little more complicated than I would have liked... I wish Haltech offered a larger set of logic/math functions like other ecu's do. I can't do very much with just AND's and OR's.  I've been asked to do fuel/ignition mapping on a medium bore engine at work in May (192L V16). Being the only programmer in my region and having went and opened my mouth about knowing the ins and outs of fuel/ignition mapping, I have now been deemed an expert. Fun fun. The entirety of the logic and algorithms are programmed in C on a PLC. As I spend more time figuring it all out, I like what I see and eventually I may consider doing the same as a pet project to replace my ecu.   
    • Dose Pipe Sutututu
      R32 GTST - 600KW+ RB28/CD009 Build

      By Dose Pipe Sutututu · Posted

      This would be interesting, would you feed it via a 2nd row of injectors? Or just usual WMI nozzles?
    • Milkmun
      Magnetic Drain Plug Snapped in Half

      By Milkmun · Posted

      Cut sump up and extend. Win win 😂 
    • SLVRBAKSLPZ
      Recommended Torque: RB26/30 ARP 1/2 Head Studs

      By SLVRBAKSLPZ · Posted

      All, What's the recommended torque for the 1/2 head studs for RB30 twin cam conversion with RB26 head?  
    • Duncan
      Magnetic Drain Plug Snapped in Half

      By Duncan · Posted

      also, we need to know which solution worked....
×
×
  • Create New...