Jump to content
SAU Community

Recommended Posts

I have an after market plummed back BOV and to be quite honest i can't say i could feel a noticable different compared to the standard.

My next step will be to try out the atmospheric bov and see if theres any difference in that.

Can anyone give any ideas on what would be more efficient? atmos bov? plummed bov?

what about the flutters (commenly known by the sound the VL's let off) is that really as bad as everyone says? if it is.. then why do a number of fast 1/4 mile VLT's have it?

Link to comment
https://www.sau.com.au/forums/topic/47522-bov-or-no-bov/#findComment-960410
Share on other sites

Well, the theory is by having a recirculating BOV, the hot air goes around again. Whereas an atmospherically vented BOV gets rid of the hot air and makes room for fresh (colder) air. There is also the cooling effect from the overly rich mixture that the engine runs after the atmosphere BOV has vented. Some people say that this overly rich mixture also reduces lag on gear changes as it burns in the turbo and helps spool it up.

You can overcome most of the stalling problems associated with an atmosphere BOV, it is a bit of fiddling though and I am not sure if it is worth it on a road car when you add in the legal issues. On the race cars we always have atmosphere vented BOV's.

Hope that helps :(

Link to comment
https://www.sau.com.au/forums/topic/47522-bov-or-no-bov/#findComment-960487
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
    • The axels in my R33 seem tired, and have a bit of play in them. I cannot find any new of course, not interested in buying used, but I am looking to see if anyone can identify some cross compatible axles. In the states I have seen suggested for S chassis the J30 axles, however for the skyline (as best I can tell) the lengths are about an inch off (2.5cm) on both sides. R33 my measure L 22" R 24.5" GPT L 22.5" 24.25" J30 L 23.5" 25.5"  so shaft length is probably an inch wider. Not sure if someone has another still remanufactured option besides the J30. I figured worst case I can buy a pair tear them down and swap the center shaft. My other option was reaching out to GSP to see if they cannot piece together a set, since the axle stubs are still manufactured, I wouldn't think it be that hard to find a shaft or make a shaft work. 
×
×
  • Create New...