Jump to content
SAU Community

Speedo problem rb25 neo swap

Shortyrock125
 Share

Recommended Posts

Shortyrock125 Rookie

Shortyrock125

Posted
Posted

What's up guys I'm new to the skyline scene I just purchased an R32 gtst with rb25 Neo. When my car was delivered the odometer and speedometer wasn't working. Took apart the dash doesn't seem like there's an issue. a friend was telling me the later year rb gets it's signal off diff, earlier rb is mechanical gets it off the trans.ones analong ones electronic? How can I fix this or is it something else ?

 

Thanks

Link to comment
https://www.sau.com.au/forums/topic/475280-speedo-problem-rb25-neo-swap/
Share on other sites
GTSBoy Grand Master

GTSBoy

Posted
Posted

You have to make a speedo drive gear for the RB25DET gearbox to drive an R32 cable drive.  The usual donor part is from a Navara, which used the same basic gearbox as RB25DET, but had cable drive.

If this has been done on your car already, then the single most likely problem is that the drive cable is broken.  They are old and they don't like the rather sharp bend that has to be put into them to fit the R32 cable onto the Navara sender conversion.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • r32-25t
      2025 Osaka Auto Messe

      By r32-25t · Posted

      I’d love to find some where that can recover the dashes to look brand new and original. Mine has a very slight bubble, nothing compared to some I’ve seen though 
    • Rezz
      2025 Osaka Auto Messe

      By Rezz · Posted

      $170K. I asked one of the guys there as a joke if that price was just for the passenger seat as it was where the price sheet was... he tried really hard to crack a smile 😄 He also mentioned that every single part of the car was inspected and either restored or replaced with a new or as new part, or made from scratch. The interior was incredible, every inch like a new car.
    • Dose Pipe Sutututu
      R32gtr sputtering and stalling

      By Dose Pipe Sutututu · Posted

      Time for a modernisation, throw out the AFM, stock O2s, ECU into the e-waste bin. Rip out the cable throttle, IACV, pedal, etc. into the scrap metal bin. DBW, e-throttle, modern ECU, CANbus wideband, and the thing will drive better than when it left the factory.
    • MBS206
      R32gtr sputtering and stalling

      By MBS206 · Posted

      I agree, don't go trusting those trims. As I said, first step is to put the logger away, and do the basics in diagnosis.   I spend plenty of time with data loggers. I also spend plenty of time teaching "technicians" why they need to stop using their data loggers, and learn real diagnostics.   The amount of data logs I play with would probably blow most people away. I don't just use it to diagnose. I log raw CAN data too, as a nice chunk of my job is reverse engineering what automotive manufacturers are doing.
    • joshuaho96
      R32gtr sputtering and stalling

      By joshuaho96 · Posted

      I'm aware, but unless you're actually seeing the voltage the ECU is seeing and you're able to verify the sensors are actually working I find it hard to just trust STFT/LTFT. I will say, logging the ECU comes naturally to me because it's one of the lowest effort methods of diagnosis and I do similar things in my day job all the time. Staring at 20+ charts looking for something that isn't quite right isn't for everyone. NDS1 allows you to log almost everything so that's normally what I do and then sort out the data later. 
×
×
  • Create New...