Jump to content
SAU Community

Recommended Posts

Hey guys,

I'm planning on doing an engine swap of an RB25DET Neo into an R34 GT and  I just wanted to check I'm on the right track and not missing any parts! The engine I'm looking to buy comes with 

*Ecu 
*Complete uncut loom 
*Coils with inbuilt igniters 
*turbo and manifold 
*Complete intake including and injectors 
*J pipe 
*Alternator 

As far as i know all I still need is an intercooler and piping

Link to comment
https://www.sau.com.au/forums/topic/475294-rb25det-neo-swap/
Share on other sites

Exhaust? Whats happening with your gearbox? Even if its factory manual you'll probably want a clutch. The brakes might need some attention too. 
 
I'm not too familiar with NEO but I believe they have a boost sensor that goes to the ecu, and of course you need the AFM.
Should've mentioned I'll be doing the clutch! Brakes are already bigger than factory too [emoji16] thanks man! Ahh exhaust, how'd I not think of that!

My advice is to sell your car, buy a GT-t

You'll save money, time, updating your registration with a new motor, etc.

But if you're dead set on doing the conversion then don't forget the boost sensor and popping in a better fuel pump.

R34 ECUs are retarded, without it the car runs like shit. Even when on Nistune, without it connected the TP Load Index goes mental, I found out the hard way when I tuned a customer's car. I disabled the boost sensor flags, upped all the voltage limits to avoid it trigger a DTC and guess what? Still went mental. Got in touch with Nistune support and they said it's paramount you connect the sensor regardless of boost or if it is disabled 

My advice is to sell your car, buy a GT-t
You'll save money, time, updating your registration with a new motor, etc.
But if you're dead set on doing the conversion then don't forget the boost sensor and popping in a better fuel pump.
R34 ECUs are retarded, without it the car runs like shit. Even when on Nistune, without it connected the TP Load Index goes mental, I found out the hard way when I tuned a customer's car. I disabled the boost sensor flags, upped all the voltage limits to avoid it trigger a DTC and guess what? Still went mental. Got in touch with Nistune support and they said it's paramount you connect the sensor regardless of boost or if it is disabled 
I thought about going this route but it seems to cost almost double in every situation considering it's about 22k+ for a gtt in NZ and 3.5 for an engine [emoji852]️, but thanks man fuel pump is definitely on the list and I'll make 100% sure about that boost sensor!
38 minutes ago, Tyler Elms said:

I thought about going this route but it seems to cost almost double in every situation considering it's about 22k+ for a gtt in NZ and 3.5 for an engine emoji852.png️, but thanks man fuel pump is definitely on the list and I'll make 100% sure about that boost sensor!

wow... they're like 12~14k here in Australia.

Just move over here, might be cheaper in the long run lol

Wow didn't realise how much cheaper R34 were in aus, although its not quite that bad, you can pick up a coupe gtt here for 18-19k if you hunt around.

3 hours ago, GTSBoy said:

Will need a gearbox.  The NA box will tap out after a year at the most.  Just not strong enough for the torque load.

I disagree with that, I had factory manual R33 20e that had been swapped to rb25det and the gearbox was fine after around 10 years on the factory turbo. Plenty of people drift with the 20e/20det style gearbox with 300+kw and get decent life out of the trans.

Wow didn't realise how much cheaper R34 were in aus, although its not quite that bad, you can pick up a coupe gtt here for 18-19k if you hunt around.
I disagree with that, I had factory manual R33 20e that had been swapped to rb25det and the gearbox was fine after around 10 years on the factory turbo. Plenty of people drift with the 20e/20det style gearbox with 300+kw and get decent life out of the trans.
I haven't seen any that low in ages! I'm happy with an engine swap anyways [emoji16] and good to know about the box! Thanks dude
57 minutes ago, KiwiBoat said:

Wow didn't realise how much cheaper R34 were in aus, although its not quite that bad, you can pick up a coupe gtt here for 18-19k if you hunt around.

I disagree with that, I had factory manual R33 20e that had been swapped to rb25det and the gearbox was fine after around 10 years on the factory turbo. Plenty of people drift with the 20e/20det style gearbox with 300+kw and get decent life out of the trans.

I disagree with your disagree. It might live 10 years in might live 10 minutes, 20 box behind a 25 is a complete lucky dip.

11 minutes ago, iruvyouskyrine said:

I disagree with your disagree. It might live 10 years in might live 10 minutes, 20 box behind a 25 is a complete lucky dip.

Thats kind of the story with any used gearbox though, especially 20+ years old. If its in ok condition and you have some mechanical sympathy its not like they are made of glass.

On another note, Ive seen 25det boxes on here for $1000-1500 which is crazy, you are out about $2500-3000 in NZ for one.

I disagree with your disagree doubly.  I have personally had 2x 20DET gearboxes suffer from input bearing death just with the increased torque load from a boosted 20 making only ~175rwkW.  My mechanical sympathy levels are off the fricking charts too.  I have also seen a large number of other 20DET and 25DE suffer short lives with 25 turbos in front of them.

The little gearboxes are not glass....they are rubber.  They are as flexible as a piece of boiled spaghetti and it f**ks about with the bearing life terribly.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hey everyone!!  I've noticed that whenever I do my oil changes, after putting 4L in, the oil level sits at the top mark in the dipstick. This is after letting the old oil drain for a very long time too! I've checked the oil level daily for the past few mornings. It happens every time and it's confusing because all the threads say that it should take about 4.7L (With some just adding the full 5L) My next thought is to figure out if the dipstick I have is correct so could someone please tell me the length of the RB25DET engine oil dipstick?  I've checked images of some of the genuine dipsticks, but none of them have the length in it. https://justjap.com/products/genuine-nissan-engine-oil-level-dipstick-fits-nissan-r34-skyline-c34-stagea-c35-laurel-y34-cedric-gloria-rb25de-t-neo?currency=AUD&srsltid=AfmBOortQXofgmiHVRKuIaiKuygL4k0Ewp68c3isGZk0vvKOJ7Yqf3iB However.... the engraving on the genuine ones say 05002 while mine says AA000. This makes me believe that maybe I have a wrong dipstick? I just want to confirm before I buy a new one. The car is a fresh import from Japan so I don't have details of the previous owner to ask him. Thanks in advance 🙏🏾 
    • Sport. I didn’t rebleed it cause I just removed the slave and left connected.    I will change line and slave and see how it goes.  
    • Oh and how is the rattle when foot is on the clutch ?
    • Did you get the sport or track ? From what the documentation says the uniclutch has a small amount of movement to disengage.  So your story of tricky pedal setup seems common.    Hopefully you got it bled up too, as the bite point moving around is usually either plates wearing in or air in the line.     
    • There's always "MIG it up and grind it back".
×
×
  • Create New...