Jump to content
SAU Community

Recommended Posts

My car has 4.3s. It's too short for my liking. My car tops out at 270kph at racetracks (not the road before you all jump in).
It's ok on the road (twisties and freeway alike), but if you have anything north of 400whp its probably not a great plan.

If I could be bothered/have the money I'd get them shortened.

1 hour ago, Steve85 said:

My car has 4.3s. It's too short for my liking. My car tops out at 270kph at racetracks (not the road before you all jump in).
It's ok on the road (twisties and freeway alike), but if you have anything north of 400whp its probably not a great plan.

If I could be bothered/have the money I'd get them shortened.

Yes especially as OP is not building a track car. Open road cruising at 3000 rev/min will soon become tiresome...even 4.1 is about 2700. Look for a complete GTR rear end ( I found one for $1200) and then you get the LSD, the axles, alloy hubs and 2 pot brakes.

  • Like 1
14 hours ago, admS15 said:

1st to 3rd is quite snappy. With 420whp, traction is a bit of an issue. If you can get it to grip, it goes like a rocket. 4th, the speed just keeps piling on.

You won't notice too much of a difference vs 4.11 other than a little quicker through the gears and a couple hundred higher rpm at cruising speed in 5th.

Yeah sounds great, thanks for the heads up.

I'm looking forward to the 4.3 as when i typed it online, it seems a fair few people have tried to convert 4.1 to 4.3 so must be for good reason.

My car will never see a track anyway, i strictly drive road only and the odd beating on a dual or motorway but nothing serious.

Traction will be because your running the stock 1 wheel spinning diff still aren't you?

If i put the super Q 1.5 way in the back, being 4wd it should grip better than a stock GTR shouldn't it?

Thanks

Arr i see, sorry thought you were 4wd..  slightly lost track of who has what in these comments.

Do you have the normal Kaaz or the WPC treated super Q in yours?

And yeah tyre's do help, the super Q transformed my GTT. I have 295 35 18 PS2's on the rear which are good but i think there's still room for improvement with the supersports or the PS4S if i could get hold of them sizes.. there supposed to be mega sticky even in crap conditions.

Yeah the 4wd is the only reason iv bought this car so i can put the power down much better and use it more 

My GTT isn't worth taking out unless its a dry sunny day and the roads are better.. too much rain and greasy roads because of buses, so if it gets moist.. full boost is pointless on rwd

My M5 has a great mech LSD diff in it and they bring the torque in later so they let you put some power down before all hell brakes lose. 

 

3 hours ago, GTSBoy said:

Almost always for drag.

 Turbo cars on the road are almost always better with taller diff ratios.

100%. The last owner of mine built it for drag purposes. I'm sure of it. 

I'm busy trying to make it a more useful road car. 

My advice would be stick with the 4.1s you'll be better off in the long run, especially if you go chasing power.
But as with all things. It's your car, you do you. :)

I have a lot to do before I decide what ratio but I might try 4.3 first,

If i’m not happy I will just change to 4.1

There’s always stock for a GTR diff and rear shafts so il be fine if I need to get hold of them 

I have about 4 months to decide so il consider the 4.1 
 
If I go 4.1, Which would be the best diff to go for from the GTR’s? An R33?
 
I have Cusco diffs in mine. They're tight as anything. 1 way in the front and 1.5 in the back. They seem to do the job well.
  • Like 1

The consensus is that the best front diff is Quaiffe and the best rear diff is either another Quaiffe (for a streeter) or a Nismo pro.

There are always votes for the other brands, as per Steve above, and they are valid.  But I have a soft spot for how nicely helical diffs drive compared to tight mechanicals.

  • Like 1
13 hours ago, Steve85 said:
14 hours ago, R34GTRSilver said:
I have about 4 months to decide so il consider the 4.1 
 
If I go 4.1, Which would be the best diff to go for from the GTR’s? An R33?
 

I have Cusco diffs in mine. They're tight as anything. 1 way in the front and 1.5 in the back. They seem to do the job well.

Okay thanks, so for say the front diff, i can order an R33 GTR front diff and itll go in my 4.1 from the NEO Turbo 4wd engine or do i need to go for a stagea front 4wd diff fitment?

Rear isn't a problem as iv seen many options for that

Its the front that seems confusing.

The engine i'm buying is just down as an RB25DET Neo 4wd.. doesn't say if its from an R34 or Stagea.. I take it both diffs for the front are the same for them, just not sure if the GTR front diff internals will go in there

10 hours ago, GTSBoy said:

The consensus is that the best front diff is Quaiffe and the best rear diff is either another Quaiffe (for a streeter) or a Nismo pro.

There are always votes for the other brands, as per Steve above, and they are valid.  But I have a soft spot for how nicely helical diffs drive compared to tight mechanicals.

Iv heard of Quaiffe but don't know much about them. I take it they specialize in Helical diff's.

I was going to leave the front diff stock to begin with anyway whether its 4.1 or 4.3, but the Rear i was going to upgrade 100% 

Il have a look at the Quaiffes and have a read up

45 minutes ago, R34GTRSilver said:

Okay thanks, so for say the front diff, i can order an R33 GTR front diff and itll go in my 4.1 from the NEO Turbo 4wd engine or do i need to go for a stagea front 4wd diff fitment?

Rear isn't a problem as iv seen many options for that

Its the front that seems confusing.

The engine i'm buying is just down as an RB25DET Neo 4wd.. doesn't say if its from an R34 or Stagea.. I take it both diffs for the front are the same for them, just not sure if the GTR front diff internals will go in there

The truth here is i don't actually know if the GT-4 is the same mechanical setup at as GTR. 
This is where my knowledge starts to run out. At the risk of being an internet jerk, see if you can search here for the data. 

Surely someone else has done something similar before. (crosses fingers on ambiguous advice). :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeah. I believe the fear of annealing the alloy and weakening it, Every online discussion has someone saying it's bad and potentially a risk when powder coating forged wheels.  
    • I'm interested if anyone agrees with what you've said, and can give a good reason. Temperature of powder coating should be below any temperature you'd use to alter the wheel structure.  Powder coat typically 200 to 250. Annealing if that's what people are claiming would be occuring, starts at 300, and depending on the alloy, can need even up at 400+.   That's the only part I can think of that could cause an issue that people are believing it's from the rim losing hardness and becoming too soft.
    • Negative probe should be on the cars chassis. Positive on the wire.   Start as said above by unplugging everything (unplug the lights, and switches. Now at the switch, there is a wire from the fuse, to the switch, so out your positive on that terminal. It should read open circuit. If it reads something, especially a stupid low value, the short is somewhere between the fuse and the switch. If that's fine, now put the positive probe on the wire that goes to the headlight (at the switch plug). If it reads stupid low, the fault is from the switch, to the headlight.   Another quick test, is take the whole LED light setup from the left, and plug it into the right side, does it still blow the fuse? If you put the right hand side led light setup on the left hand side wiring, does the left hand side wiring now blow?  If the blowing fuse swaps from right to left doing this, your LED lights are the issue.
    • Anyone know if it's a problem to powder coat forged alloy wheel centers (Rays/Volk GT-C). some say it's bad and can damage the alloy, some say it's not a problem.
    • Hey guys, I'm reviving an old post but I'm finally getting around to working on this now. I removed the battery to get a better look at the wires and i traced the wires from the headlight to the fuse box in the engine bay, but the wiring looks fine? The wiring for the R/H headlight is 3 wires and then is bundled up with the large diameter wire that goes underneath the fuse box. I didn't take it apart yet. I know you said that its a short circuit somewhere between the fuse box and the headlight. But could it be the headlight switch on the dash? Also, i pulled out my multi-meter and set it on the Ohms, but i'm not sure where to put the negative probe and the positive probe.     
×
×
  • Create New...