Jump to content
SAU Community

Finally.... the car of my dreams

hcr32ROB

By hcr32ROB,
in Introduce yourself

 Share

Recommended Posts

Robocop2310 Experienced

Robocop2310

Posted
Posted
10 minutes ago, Ben C34 said:

Man you are a genuine tool. Good on ya.

If the gtrs complete you I think you will find it is you with the inferiority complex.

anyway, you have a lot to learn about everything so I'll leave you be to figure out some important life lessons. Rethink choices, contemplate naval etc.

No need to reply. Just as per every other completely nonsensical arguing you have put forward it gets you, and everyone else, no where.

peace out. Go drive a gtr slowly around the place enjoying all that awd has to offer.

Alright mate. Good on ya. 

niZmO_Man Grand Master

niZmO_Man

Posted
Posted
15 minutes ago, hcr32ROB said:

I’m praying to the skyline gods that the build/mod thread for this car is nowhere near as controversial as this introduction ???

Bored people who over paid for their $40k coupes :P 

I miss my R32 GTS-t, was loads of fun to drive around, even in traffic and crappy roads. Completely standard, sunroof, easy on fuel, lightweight (chuckable). Shame my dad wrapped it around a pole, now I have a GT-R that's too harsh to drive around on the roads all the time (I started modding it for track work), oh well.

Your car looks good. I'd personally go the Type M front bumper as I think the fog lights in it look better than the tacked on GT-R bumper ones.

  • Like 1
hcr32ROB Apprentice

hcr32ROB

Posted
  • Author
Posted
1 minute ago, niZmO_Man said:

Bored people who over paid for their $40k coupes :P 

I miss my R32 GTS-t, was loads of fun to drive around, even in traffic and crappy roads. Completely standard, sunroof, easy on fuel, lightweight (chuckable). Shame my dad wrapped it around a pole, now I have a GT-R that's too harsh to drive around on the roads all the time (I started modding it for track work), oh well.

Your car looks good. I'd personally go the Type M front bumper as I think the fog lights in it look better than the tacked on GT-R bumper ones.

Yeah yeah I see what you mean with the front bumper- 2 options I’m considering. Still undecided ?‍♂️ 

1- gtr bumper and getting new mesh and remove lights

2- going to type m with standard spot lamps 

 

jmknights93 Mentor

jmknights93

Posted
Posted
32 minutes ago, niZmO_Man said:

I miss my R32 GTS-t, was loads of fun to drive around, even in traffic and crappy roads. Completely standard, sunroof, easy on fuel, lightweight (chuckable). Shame my dad wrapped it around a pole, now I have a GT-R that's too harsh to drive around on the roads all the time (I started modding it for track work), oh well.

I can agree with the statement. I miss my old GTS-t also. I hardly drive my GTR now.

GTSBoy Grand Master

GTSBoy

Posted
Posted

Yes and no.  Or, more correctly, no and yes.  Guards have nothing to do with bonnet and grille fitting.  GTR grille does only mount off of GTR headlights.

I have GTR bonnet, grille, headlights & bumper on my car, with GTSt guards.  The proper GTR bumper is slightly too wide/wrong shape to be squeezed onto GTSt guards, but it does fit.  There are repro GTR bumpers made to suit GTSts without that extra little bit of width.

It's possible that there are probably imitation/fake GTR grilles available somewhere that can mount onto a GTSt front end without having to have the right headlights, but I've never looked into it.  I say this because of the existence of GTR style bumpers to go on GTSts....there would need to be a way to fit the grille without having to have the headlights too.

Having said all that, in this day and age of 3D printers and Sikaflex, it should actually be possible to come up with something to stick onto GTSt headlights that would provide the GTR grille mounts.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • soviet_merlin
      Magnetic Drain Plug Snapped in Half

      By soviet_merlin · Posted

      Half anticipating the next question then: I have two magnets stuck in my oil pan. What should I do? 
    • joshuaho96
      Magnetic Drain Plug Snapped in Half

      By joshuaho96 · Posted

      If it's magnetic what is stopping you from using a magnet on a thin wire from fishing it out?
    • dbm7
      Shifting questions

      By dbm7 · Posted

      Those 2 solenoids in that assembly I mention, are the PWM solenoids for torque converter lock-up clutch & EPC (line pressure control) ~ when most folks hear of 'solenoid failure', the tendency is to think electrical failure...but fact of the matter is, especially wrt the EPC solenoid (which is moving/running all the time), you can have an electrically 'good' solenoid, that's absolutely broken/worn out mechanically inside...ie; valve plunger return spring rubbing against spring retainer plate, lowering preload pressure.. ...and the solenoid armature extension limit spring wafer with bad wear/broken off petals... ...and if there's ever been any metal flying about, damage to the valve plunger end itself... ...the stuff one never really sees, unless you go the whole 10yards trying to answer the question "why is my line pressure screwy, but TCU isn't flagging any EPC solenoid fault?"...and carefully dissect the solenoid. Worst (and most probable) scenario is when the plate spring petals break off, they get held by the magnetic flux, get mashed up by the armature into little bits, which end up in the space between the armature & shading core bore, and things get stuck or randomly jam up, and your line pressure goes flat and doesn't change...and the TCU never sees it, as it doesn't actively monitor LP... ..then it gets into insidious land, if you end up with lower than expected line pressure...lets say high clutch..and the lower pressure causes it to slip ~ when I say 'slip', think say 2000rpm on the drive plates, and 1800rpm on the driven plates, because the slip is making them under-rotate by 200rpm ; you get all the usual nasties like heat and band/clutch wear, but even if it's only 20rpm slip the same thing happens...and... you'll hardly ever pick this up driving the thing with the torque converter active as it effectively masks these sorts of slippages that are line pressure related ...(the newer TCUs can detect clutch slip rate)...just  FYI as it were...  
    • GTSBoy
      MAJOR FUEL ISSUES 25det neo r32

      By GTSBoy · Posted

      There's nothing that some paddle pop sticks and extra cable ties can't fix.
    • QB6SAGR
      RB20 in need of modest love injection

      By QB6SAGR · Posted

      Hey guys, so Golebys has good prices on Bosch injectors, and also sell an adaptor to go from 1/2 length injector to standard with the Nissan 10.5mm top seal.  Does anyone know if that adaptor is to suit the 14mm or 11mm injector tops?  And re. The bottom seal, to suit my standard RB20 intake, would I be right in saying I can just slip the 14mm square section O ring over the bottom of the new injector and done? Thanks in advance guy, Cheers, Rowdy
×
×
  • Create New...