Jump to content
SAU Community

RB cylinder head identification listing

iruvyouskyrine
 Share

Recommended Posts

iruvyouskyrine Grand Master

iruvyouskyrine

Posted
Posted

Hey all,

Decided i would knock this up to help people ID what cylinder head they have. The list is mostly complete and i should have it finalized in the next day or two.

If people could cross check with what they have on their vehicles that would be awesome.

The casting ID is located somewhere around cylinder 1 and is ia 3 number/digit code. Attatched is a pic of an RB20DET so you can see the casting number.

Cheers

73L.jpg

RB ID.JPG

  • Thanks 1
Rusty Nuts Experienced

Rusty Nuts

Posted
Posted (edited)

If you want to confirm the casting numbers they are the 6th, 7th, and 8th numbers in the Part No.

ie R33 RB25det  part. no. 1104075T00

    R33 RB25de    part no.  1104075T00

     R34 RB20det  part no.  11040AA000

Edited by Rusty Nuts

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Shoota's R33 GT-R RB30/26

      By MBS206 · Posted

      I was more thinking so it doesn't flop around as much rather than for rotating it. Once you have the balance right, it should rotate well enough, depending on how much resistance there is on the pivot. I think you said the pivot point was on a bearing though didn't you?
    • Shoota_77
      Shoota's R33 GT-R RB30/26

      By Shoota_77 · Posted

      You can get them with the worm drive rotator but I was too tight to pay another $250-$300 so manual labour it is! I don't think it will be too hard to rotate though. 
    • MBS206
      Left & Right Window Regulators for 2013 Skyline V36 Coupe

      By MBS206 · Posted

      Sag as in the windows start to slowly open themselves, or they're just slow to go up/down with engine off?
    • MBS206
      Shoota's R33 GT-R RB30/26

      By MBS206 · Posted

      It looks like it needs a big worm gear drive on it to control the rotating, not a few sloppy pins!
    • MBS206
      R32gtr sputtering and stalling

      By MBS206 · Posted

      As Duncan said, first there was OBD, which few cars used, then came OBD2.   Now an interesting point, OBD2 isn't even for what you want to do. OBD2 is for emissions testing. There is some sensor data on OBD2, but it's up to the manufacturer what they're putting on it. Most scan tools operate on UDS, which like OBD2 is a standard built on-top of CAN. UDS specifies how to structure a message, what very limited things mean such as "read memory address" but it does not specify what is stored in which memory address, that is all up to the manufacturer. You either a scan tool compatible with that vehicle, or to know how to reverse engineer all the data, which can take a VERY long time and a lot of vehicles to get it right. Oh and then the manufacturer does a firmware update and changes what's where... Ask me how I know that as fact Oh, and by the time you've got the scan tool that supports all the manufacturers stuff, well, you're back at "But a consult cable and the Nissan software" The main difference being most manufacturers software these days works with the same hardware readers, as the readers are built to support J2534 which is another standard for how the PC communicates with the tool to make it do specific things on the car...
×
×
  • Create New...