Jump to content
SAU Community

Wiring horn

drifter17a

By drifter17a,
in Engines & Forced Induction

 Share

Recommended Posts

drifter17a Rising Star

drifter17a

Posted
  • Author
Posted

There is a 10 amp fuse

 

My question is, if for whatever reason the ground that is short circuited then will it sound the horn until battery is drained or somehow fuse will blow. I think it is the first case as the fuse is 10amp and horn pulls way less so it will work and work until battery is dead

 

my setup is, 30 and 85 are joined and then fused to the battery on 10 amp

drifter17a Rising Star

drifter17a

Posted
  • Author
Posted

Well here is the story

 

my cheap boss kit broke which had a brass at the back, i bought a hkb boss but there is no brass/copper at the back so i have ran the wire inside of the boss hole and checked the wire has clearence to turn from side to side however if wire is snapped then ground could be short and hence horn going off

KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

It is theoretically possible but most unlikely that the wire will break and short out in the middle of the night. It is more likely to break while you are driving it and you can do something about it.  You should be more worried about Brexit and Global climate change.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • carnoobb
      V35 Overheat + Coolant Boil & Overflow + Engine not Starting

      By carnoobb · Posted

      Hey all, my 2004 Nissan Skyline 350GT overheated the other day with coolant boiling and leaking out of the coolant reservoir when I was parking. So today, I started it up again just to see if it was a thermostat/head gasket issue. After about 20 mins of running, temps were normal again, no coolant was leaking out and the upper reservoir hose was warm but my engine suddenly cut off. I checked the oil dipstick and cap when it was running and there was no white foamy residue and the exhaust did not have white smoke. I tried starting up the car again but it would only crank, similar to when I had a camshaft sensor issue just that now there’s no check engine light on the dash. Any ideas? Unfortunately I don’t have an OBD2 that can read the Nissan's programme.
    • Papichulo96
      Rb head oil drain dimensions

      By Papichulo96 · Posted

      Bump on this to not make another post, had a ‘head drain’ leak on me and have the engine out as we speak. Planning on just putting a new freeze plug back in , plug the tapped holes and just be done with that headache.    Now I still want to relieve pressure to allow oil to pass down the blocks returns easier. I’ve seen catch cans with multiple vents help folks with this issue on this forum.  I’m wanting to make my own. I have some pictures here of my setup if anyone can help how I should plumb and design the catch can I would deeply appreciate it !   rb25 Oil upgrades: 1.0mm restrictor n1 pump/billet gears extended crank collar  extended sump with trap doors/w welded fitting    
    • GTSBoy
      Need AC Compressor for R32

      By GTSBoy · Posted

      The Frenchy's kit is the way to go forward. A modern compressor that weighs about 1/2 as much, is at least twice as efficient, and will do a good job on R134a. And of course the kit has everything else you need to connect it up and have it work properly.
    • Zabuza
      Need AC Compressor for R32

      By Zabuza · Posted

      Hey all , I am in the process of having the AC system in my r32 GTST converted from r12 to r134a and I’m being told my compressor has gone bad and I will need a new one. I was wondering if anybody has any suggestions for what is the best route to go aside from dropping $1500 on a new oem one? I did see that Frenchy’s performance garage offers a kit to mount a Toyota compressor, has anybody actually used this kit on their car? Or is there anywhere I could purchase just a clutch? Any help is appreciated.
    • GTSBoy
      Help Understand GTT Boost Setup

      By GTSBoy · Posted

      Well, your RB20 ECU loom won't have wires for the boost solenoid, that boost sensor, and possibly one or two other things. There could be differences in seemingly random things like the charcoal canister purge solenoid, because the 25DET has to handle boost in the vacuum system and the 20DE does not. I don't know - I haven't looked. It is very likely that all the most important things are same-same, being the main sensors like AFM, CAS, etc, and the injectors and ignition. Not that you'll need the AFM for the Haltech anyway. I would suggest that you would seriously want to sit down with the pinouts for both ECUs and just go through them and highlight green what is the same, orange what is different/missing, and make a plan from there. It's not going to be difficult. It will either be the same or need to be fixed.
×
×
  • Create New...