Jump to content
SAU Community

Recommended Posts

Sup guys,

 

In another thread I mentioned my car came with a dyno sheet which I think is wrong / has been tuned since then.

It's got manifold gauge pressure on the right and it hit 31 psi. As far as I know this isn't boost pressure, it's engine pressure + boost pressure?

Or something like that.. What pressure does the GTT run at stock? Trying to work out how much boost it was at during this run.

 

Cheers

Link to comment
https://www.sau.com.au/forums/topic/476109-how-to-read-this-dyno-chart/
Share on other sites

Stock boost on a Neo is only 7 psi.  5 at the wastegate spring, + 2 from the stock bleed valve.  With better exhaust etc it might run a little higher, but not 12.  Takes a boost controller to get it above 10 usually.

There's no such thing as "engine pressure + boost pressure".  31 psi makes no sense unless you have a very large turbo shoving a lot of air down the engine's throat.  How much power did it make?

  On 21/02/2019 at 7:35 AM, GTSBoy said:

Stock boost on a Neo is only 7 psi.  5 at the wastegate spring, + 2 from the stock bleed valve.  With better exhaust etc it might run a little higher, but not 12.  Takes a boost controller to get it above 10 usually.

There's no such thing as "engine pressure + boost pressure".  31 psi makes no sense unless you have a very large turbo shoving a lot of air down the engine's throat.  How much power did it make?

Expand  

That's the one I mentioned in the other thread making 181kw. Manifold gauge pressure reads 31psi. It's definitely a lot more than 181kw, GT3076, pulls quite hard, e.g I can hit 16psi in second gear easily

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I mean, if you were to move the jacking points away from the original location, that is, away from the wheels and closer to the centreline of the car, then it will be more likely to overbalance and tip off the supports. Same as we talked about before. I was talking about moving for-aft. If the sill is bent outward or inward, then the car would obviously look unstraight from the outside. Hopefully that hasn't happened either. Again, you can do comparative measurements from the chassis rails to see if there is much deflection.
    • Can you elaborate what you mean with your first sentence? I meant move as in the bulge kinda seemed like it got pulled "outward" meaning it got pulled down and to the side with the jacking rail itself, so the load bearing bulge now sits lower than usual and is not level with the sill on the other side of the jack point. Either that or the jacking rail just got pushed in a good bit.
    • As well as being risky WRT tipping off anyway. Yeah, I wouldn't expect it to move. Just measure from the rear one to the front one on the good side, then measure that same length on the wrecked side. You will find the notches in the pinchweld, and the jacking pad. Just spray a spot of marker paint or something there.
    • but any other area than the bulge you are talking about will just cave in then? The front driver side is pretty bent so I don't know if that will work the way it is now. I can still kinda make out where that bulge is/was but it looks like the position of it also changed due to all the mistreatment? Hard to tell
    • Absolutely. Look very closely at the photo (of yours) that I took my second snip of. See how the sill is thicker material right behind the pinchweld, where the two notches are? That is the factory reinforced area for lifting. That pad is supposed to carry the weight. The factory jack (go look at it, and how it interfaces with the car at the pinchweld) shows you exactly how the load is carried from the car to the jack to the ground.
×
×
  • Create New...