Jump to content
SAU Community

Lag between gears after GTX upgrade

Boosted Esky

By Boosted Esky,
in Engines & Forced Induction

 Share

Recommended Posts

Boosted Esky Explorer

Boosted Esky

Posted
Posted

I've recently swapped out a GT2860RS for a GTX2860R Gen2 and had the engine retuned. There's a tiny bit of lag when changing quickly from 3rd to 4th, 4th to 5th. This never happened with the GT. Could it be that the billet wheel has less inertia and therefore slows down more between gears? The other changes made aside from the turbo is a larger 32mm plumb back BOV relocated to the  throttle body side of intercooler (old BOV was 25mm and on the turbo side) and the pipe between turbo and intercooler stepped up from 2" to 2.5" . I've noticed if the BOV is set too soft the lag was worse. I have set it fairly hard but the lag persists.  Just wanting some advice so I'm not wasting time changing things that don't need to be changed eg: changing the 2.5" IC pipe to 2". I get the feeling this is just a characteristic of the GTX turbo?? Thanks in advance

  • Like 1
Link to comment
Share on other sites
The Bogan Grand Master

The Bogan

Posted
Posted

How much pressure does the BOV hold, if your dumping all your pressure you might want to adjust your BOV till it just starts to flutter, a bit.

I believe doing this fixed, a bit, the same issue I had with my STI.

I Basically tightened the thing down till it made the pigeon love call, a bit....

There was no real science behind this, I just wanted the BOV to not dump all the air, how much pressure was retained, f**k knows.

Someone smarter will most likely call me a idiot, won't be the first time.....

  • Like 1
Link to comment
Share on other sites
Slap Rising Star

Slap

Posted
Posted
I've recently swapped out a GT2860RS for a GTX2860R Gen2 and had the engine retuned. There's a tiny bit of lag when changing quickly from 3rd to 4th, 4th to 5th. This never happened with the GT. Could it be that the billet wheel has less inertia and therefore slows down more between gears? The other changes made aside from the turbo is a larger 32mm plumb back BOV relocated to the  throttle body side of intercooler (old BOV was 25mm and on the turbo side) and the pipe between turbo and intercooler stepped up from 2" to 2.5" . I've noticed if the BOV is set too soft the lag was worse. I have set it fairly hard but the lag persists.  Just wanting some advice so I'm not wasting time changing things that don't need to be changed eg: changing the 2.5" IC pipe to 2". I get the feeling this is just a characteristic of the GTX turbo?? Thanks in advance

They are correct about the amount of air that has to be compressed, even though it flows more it won't have as much response due to the time it takes to spool enough boost.

Also the larger bov will allow quicker and more air to be released meaning even more to fill. That's why adjusting it will help a bit.

 

On the bright side your car should make more power up higher in rpm with 2.5" over 2".

 

 

Also worth a mention is that the plumb back needs to be between the afm and turbo as it has usually accounted for the air blown off.

I angled mine to shoot at the turbo fins to help keep inertia.

If it's to close to the afm or it blows back through it ...isn't great.

  • Thanks 1
Link to comment
Share on other sites
Boosted Esky Explorer

Boosted Esky

Posted
  • Author
Posted

Wow a lot of replies thanks. There's no AFM and plumb back is angled on the intake so that's all good. I actually just had the car at the drags Wed night and have gain 3 tenths of a second with this new set up so I'm pretty happy with where it's at. BOV is set hard so it doesn't dump all the charge and the 2.5" pipe doesn't seem to affect things too badly now that I've had a good chance to test it. I'm sure though that a 2" pipe would improve the symptom.  Cheers

  • Like 1
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      From there, as the manual says....assembly is the reverse of disassembly, no tricks worth mentioning Much better (for me)
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      In my case, the standard wheel I had was in good condition but the buttons had more wear, so I swapped them across from the original wheel from the car. The plastic rear cover is held on by 4 tabs, and once the wiring is removed you can get access to 2 screws on each side the hold the buttons in From there I just swapped the wiring over. What was interesting is the standard style wheel is 2.0kg but the carbon fibre one is 50% heavier at 2.9kg. It even has a weight inside the wheel at the top to make up for some sort of imbalance in the design. weird
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Once the airbag is off, to remove the steering wheel.... Undo the 2 plugs into the clock spring, and the horn connector from it's clip. Hit the 19mm nut with a rattle gun (preferably) or if you don't' have one, you probably want an assistant to hold the wheel in place while you use a breaker bar to undo the nut Then, screw the nut back on 3 turns, and pull the wheel sharply towards you. If that doesn't work hit it medium force with a rubber mallet on either side, or possible behind if you can get there. If that all fails (it shouldn't!) you might need a steering wheel puller
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So, to next task....the carbon fibre steering wheel was either an expensive factory option or a chinesium special. Either way, I don't like either the flat bottom or thick ring style, so it had to go So...to remove the steering wheel.... First, disconnect battery negative and stomp on the brake pedal for a few seconds. Then, remove the small circular covers on each side of the wheel's rear surround to uncover the airbag clips. You need to push something like a flat bladed screw driver through, to push the steel clip inwards and pull the side of the airbag forward. Once you've done the easy side, same on the centre console side. You can see the tab you are shooting for circled in red Then, disconnect the horn spade connector and for the yellow airbag plug you need to get something small under the black locking tab to pop it out, then the connector releases......airbag is off  
    • alexburns
      Interior Light Problems

      By alexburns · Posted

      @99RS4just wondering if you ever took photos of the footwell lighting / how you bypassed the controller, im keen to haver footwell lighting come on when I open the doors too   
×
×
  • Create New...