Jump to content
SAU Community

Work to be done on my 350GT

jsmit94
 Share

Recommended Posts

jsmit94 Apprentice

jsmit94

Posted
Posted (edited)

Hi all.

Recently had my 350GT (purchased 2 months ago) serviced and was told I had the following issues with approx. prices to have them fixed:

* Rear brake pads (estimated approximately $180)
* Inoperative high mount stop lamp (estimated approximately $250 repaired/ approximately $190 second-hand)
* Front lower control arms (estimated approximately $800 for both sides)
* Worn rear sway bar links (estimated approximately $250 for both sides)
* Worn rear wheel bearings (estimated approximately $1100 for both sides)

How are the prices on these? They seem excessive but just wanted someone with knowledge to validate it for me.

Cheers!

 

 

 

 

 

Edited by jsmit94
Link to comment
https://www.sau.com.au/forums/topic/476814-work-to-be-done-on-my-350gt/
Share on other sites
Leroy Peterson Grand Master

Leroy Peterson

Posted
Posted

Did they say what's wrong with the front control arms? Could the bushings just be replaced for a lot of those?
SuperPro/Whiteline make a lot of bushings for V35.

Some of those prices seem a bit steep, depends on if they're using OEM parts and what their hourly rate is for labour.

jsmit94 Apprentice

jsmit94

Posted
  • Author
Posted (edited)
1 hour ago, Leroy Peterson said:

Did they say what's wrong with the front control arms? Could the bushings just be replaced for a lot of those?
SuperPro/Whiteline make a lot of bushings for V35.

Some of those prices seem a bit steep, depends on if they're using OEM parts and what their hourly rate is for labour.


 

Well he said that the bushes were 'broken', and then he said the whole control arms need replacing. 

The cars steering pulls pretty badly to the left, is this a symptom of that?

Edited by jsmit94
GTSBoy Grand Master

GTSBoy

Posted
Posted

The brake pad price is fine, for decent pads + fitting.

The highmount brake light price could be fine or it could be ridiculous.  Depends on why it's dead, what needs to be replaced.

i concur with Leroy that the rest of the prices look a bit mad.  I wouldn't expect to pay that much for the rear wheel bearings.  Maybe half that, maybe a bit more than half. The control arms almost certainly don't need to be replaced.  New bushes.  The ARB links can't be that expensive.  I just put 4 onto my car for less than that.  The most expensive Whiteline ones are only ~$150 and they take 15 minutes to swap on the hoist.

DashyyPC Collaborator

DashyyPC

Posted
Posted

Holy shit that wheel bearing price....

I just had both the rears done on my v36.. $250 for brand new ones shipped and $220 for installation. 
$1100 is insane.

Rear brake pads you can do yourself (unless you prefer not) and save the labour cost.
 

jsmit94 Apprentice

jsmit94

Posted
  • Author
Posted (edited)
2 hours ago, The Max said:

Your mechanic is (figuratively) a rapist. Find someone either honest or who actually knows how to fix cars with the right amount of effort and parts.

yeah seems like it now.. Thought I could trust someone who says they have worked as a mechanic in Japan, says they specialise in Jap imports and actually sources parts through their Japanese business to not rip me off, considering the experience they have. Does anyone have any recommendations for someone to go to in Sydney? 
I'm from around Bankstown, so anywhere closeish to me (an hour away max) would be awesome.

Edited by jsmit94
DashyyPC Collaborator

DashyyPC

Posted
Posted
8 hours ago, jsmit94 said:

yeah seems like it now.. Thought I could trust someone who says they have worked as a mechanic in Japan, says they specialise in Jap imports and actually sources parts through their Japanese business to not rip me off, considering the experience they have. Does anyone have any recommendations for someone to go to in Sydney? 
I'm from around Bankstown, so anywhere closeish to me (an hour away max) would be awesome.

To be honest dude my local ultratune services mine. Majority of 350z parts will fit your car so any mechanic will do it fine.

  • Like 1
The Max Mentor

The Max

Posted
Posted

Go to Adrian's Auto Centre at 100 Parramatta Rd Croydon. The workshop access is in the lane behind the car dealership. He's the guy I go to when it's not something I can do in my own driveway. No, he doesn't charge dealership prices and definitely runs an honest workshop.

niZmO_Man Grand Master

niZmO_Man

Posted
Posted
11 hours ago, jsmit94 said:

yeah seems like it now.. Thought I could trust someone who says they have worked as a mechanic in Japan, says they specialise in Jap imports and actually sources parts through their Japanese business to not rip me off, considering the experience they have. Does anyone have any recommendations for someone to go to in Sydney? 
I'm from around Bankstown, so anywhere closeish to me (an hour away max) would be awesome.

I've been working on Japanese cars for over 25 years (I'm 30), I can source parts directly from Jesse Streeter (who lives in Japan) and partsouq (UAE).

Don't believe everything people say.

junkie Mentor

junkie

Posted
Posted

I sorted the high mount stop light on my old 250GT for $12.50 plus my own time - bought a Red 12 volt SMD LED strip from eBay, mounted it to a piece of black plastic and glued the whole thing into the existing housing. Looked great, worked great, passed inspection with zero issues

jsmit94 Apprentice

jsmit94

Posted
  • Author
Posted
1 hour ago, niZmO_Man said:

I've been working on Japanese cars for over 25 years (I'm 30), I can source parts directly from Jesse Streeter (who lives in Japan) and partsouq (UAE).

Don't believe everything people say.

I guess it was more the reviews on their business that made me believe them, didn't expect someone with such good reviews to be so overpriced lol. I don't doubt that their work is good, but price-wise I think I will go elsewhere.

jsmit94 Apprentice

jsmit94

Posted
  • Author
Posted
On 4/29/2019 at 3:15 PM, DashyyPC said:

Holy shit that wheel bearing price....

I just had both the rears done on my v36.. $250 for brand new ones shipped and $220 for installation. 
$1100 is insane.

Rear brake pads you can do yourself (unless you prefer not) and save the labour cost.
 

Where did you order the bearings from?

jsmit94 Apprentice

jsmit94

Posted
  • Author
Posted
21 hours ago, fatz said:

Cofff have whole rear hubs in Sydney for a slab of beer

 

cooooofffdddd

haha I appreciate the offer man but because this car came with no evidence at all of any work that was done to it, i'd rather go to a place where I can get a tax invoice to show for it. Thanks anyways legend ?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      RB20 in need of modest love injection

      By GTSBoy · Posted

      As you're looking at using a Link ECU, then large injectors are not a problem. But there's not really any need to go 1000s on an RB20 unless you're planning >>600HP on E85, which would seem unlikely. There are other options for injectors. The Xspurt ones are available from a number of places and you can get them in the mid 600s and 725cc, which is probably a sensible place to be. These are all EV14 based. If you are not using the stock AFM (at all, which would be the case with a Link) then a large turbo intake pipe to suit the ATR turbos is not an obstacle, so you should use one instead of a highflow. Results will be better.
    • QB6SAGR
      RB20 in need of modest love injection

      By QB6SAGR · Posted

      Hey guys,  I'm after some advice and this here is the best place to get it imo. I was a member a looong time ago under another account, with a lost email address. Its nice to jump back on and see some of the same names still giving good advice.  I mothballed my car when i moved to perth in 2013, and after getting towed across the nullabor a few times it has officially done more km's on a trailer than under its own power. Now that i have started the process of tidying up and modifying it, i see the fruit available (and the fruiterers selling the produce) is different than back in the day. hence my questions, as i used to 'know' what to get and now, i'm not so sure. Engine wise the car (92 gtst) has a walbro 255, k+n, fmic, cam gears and and turbo back 3"exhaust. Wish list is a Hypergear high flow or ATR43G1, Link G4x and some newer injectors before a tune up. My goals are modest, only low 200's power wise. i know i could achieve this with less, but i've been swapping out old for new where i can. Every cooling hose has been replaced, along with mani gaskets, WP, thermostat and radiator, fuel pump and timing belt, tensioner and idler, and i rebuilt the steering rack. Regarding the injectors, the fruiterers all seem to sell what used to be considered quite large injectors. There are a lot of options for bosch 1000cc EV14's, and i would like to know if that is a suitable choice for my build. Is modern injector design good enough to run these at the low duty cycles that i likely would be? is there a downside to running a too large injector these days? or, would there be an upside to running a smaller injector at higher duty cycle? I can see that there are smaller injectors still available, but the ones i have seen specifically marketed for RB's are pretty large (see: https://golebysparts.au/collections/fuel-rail-injector-kits/products/nissan-rb20-fuel-rail-bosch-980cc-1150cc-injectors-turbosmart-fpr800-regulator-kit), and i dont know enough about them to say one not marketed for RB's would fit or not. I have searched the forums, and amongst all the posts on older tech, I did see gtsboy recommend EV14's, but no size was mentioned... again, i'm not clear on if the smaller size bosch injectors are also EV14's as they do look similar.  also, if someone can recommend a tuner familiar with RB's in the Geelong or West Melbourne area i'd appreciate it. Thanks in advance guys. Cheers, Rowdy  
    • Duncan
      R33 GTR lift points for hoist

      By Duncan · Posted

      FWIW the depth of the groove in the rubber pad is not super essential, the blocks are rubber and squish a bit. If you are worried an angle grinder will make a deeper groove quick smart
    • GTSBoy
      R33 GTR lift points for hoist

      By GTSBoy · Posted

      I mean, if you were to move the jacking points away from the original location, that is, away from the wheels and closer to the centreline of the car, then it will be more likely to overbalance and tip off the supports. Same as we talked about before. I was talking about moving for-aft. If the sill is bent outward or inward, then the car would obviously look unstraight from the outside. Hopefully that hasn't happened either. Again, you can do comparative measurements from the chassis rails to see if there is much deflection.
    • sunsetR33
      R33 GTR lift points for hoist

      By sunsetR33 · Posted

      Can you elaborate what you mean with your first sentence? I meant move as in the bulge kinda seemed like it got pulled "outward" meaning it got pulled down and to the side with the jacking rail itself, so the load bearing bulge now sits lower than usual and is not level with the sill on the other side of the jack point. Either that or the jacking rail just got pushed in a good bit.
×
×
  • Create New...