Jump to content
SAU Community

Wolfv4 map rb20det ?

Slap

By Slap,
in Engines & Forced Induction

 Share

Recommended Posts

Slap Rising Star

Slap

Posted
Posted

Any one got a rb20det base map file for a wolf v4 plugin , that they would be willing to share with me?

 

I want to have a play but am new to wolf and am unsure of a couple of the settings to get correct injector/spark order, as the wolf v4 unit may have 25det tune.

 

I contacted wolf and the unit does both 20/25 without any wire changes.

 

Link to comment
Share on other sites
Slap Rising Star

Slap

Posted
  • Author
Posted

As far as i could see in the downloads the maps they have are for 25.
The boss man at wolf said it could be tuned to suite 20 and the injectors/spark pins shouldnt need swapping to correct.

Surely someone with a 20det map or some know how on these old wolf v4 plug in units.

Link to comment
Share on other sites
GTSBoy Grand Master

GTSBoy

Posted
Posted
17 minutes ago, Slap said:

The boss man at wolf said it could be tuned to suite 20 and the injectors/spark pins shouldnt need swapping to correct.

Yuh, that's my point. 3 injector drivers, 3 coil drivers. These are in pairs, so the chances of getting them wrong between near identical engines is really small.  It's firing the opposite cylinders at the same time, every revolution of the engine. Just wire it up. If it fires, you got it right. If it doesn't, there's only 2 more permutations of connections to try.

  • Like 1
Link to comment
Share on other sites
Slap Rising Star

Slap

Posted
  • Author
Posted

Its plugin so wiring it up is prety easy. Lol.

Hmmm wonder if its the same 2 firing and that may be why it works on 20 det...

If i recall its cyl 4 and 6 that are different pins between the 25 and 20 ecu.

Thanks for the info. Ill do some sussing.

Still would be nice to get a gold of a base map for the 20 oposed to the 25.

Link to comment
Share on other sites
Slap Rising Star

Slap

Posted
  • Author
Posted

Isnt there an injetor on a different pin for the 25 compared to the 20?

Use the 25 map and pull out timing on the cruise/vac area to start.
Or download haltech ecu manager and open up a RB20DET map and transpose the data into Wolf.
Also all RBs have the same firing order.
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Does anyone know whats happening with harness on drivers door?

      By GTSBoy · Posted

      The two diagrams are equivalent. The R32 one is just one sheet out of about 3 showing everything in the whole car all at once. And without knowing the functionality that occurs in the modules, they are both equally opaque.
    • Neostead2000
      R35 OEM Injector dead times

      By Neostead2000 · Posted

      8v - 2.48ms 9v - 2.15ms 10v - 1.74ms 11v - 1.41ms 12v - 1.15ms 13v - 0.99ms 14v - 0.89ms 15v - 0.82ms 16v - 0.81ms I'm running these values on my RB20 Neo with 570cc Denso R35 stock jets and it's great. Also bought a set for my Legnum VR4, love these injectors!
    • harambe34
      Does anyone know whats happening with harness on drivers door?

      By harambe34 · Posted

      Thanks for your reply,  Those blue/green wires running to the actuator aren't attached to anything, so I'm not sure how the central locking is still working. I will have to take a good look tomorrow, I don't have the car with me. After googling it seems like a pretty common aftermarket actuator which even uses the same green/blue wires the immobiliser required. i'll test everything tomorrow and if it's working i'll melt the solder, strip it, resolder and neaten it all up with some heat shrink. I don't have to understand it if it works hahaha I just don't want a fire/ short circuit. That R32 diagram looks more like a continuity chart? Can you make sense of this form the R34 manual? 10V is probably due to very flat battery, i'll recheck as well tomorrow, I did have to jump start it haha. Thanks again!  
    • GTSBoy
      Does anyone know whats happening with harness on drivers door?

      By GTSBoy · Posted

      So, COM doesn't mean comms. It means common. What common itself means will depend on the type of device. For a two directional actuator (ie, one that can push and pull on the same output rod) then the common will typically just be the earth connection. There will be at least 2 other wires. If you put 12V on one of the other wires, then the actuator will push. On the other 12V wire, it will pull. Can't quite make out what is going on with the wiring of your actuator. It appears to have several wires at the actuator plug, but there only appears to be 2 wires where its loom approaches the door control module, with at least one of the others cut off. I don't know these actuators off by heart. I'd have to look at a wiring diagram for one before knowing what the wires were about, and that's despite me having to replace one in my car not all that long ago. Just not interesting enough to have dedicated memory set aside for trivia like that any more. That actuator is an aftermarket one, not the original one, which probably died and was replaced. That might require some sort of bodge job on wiring to make it work. Although nothing should justify the bodginess of the bodge job done. As to the soldering job on the door module's loom plug. Ahhahhahaha. Yes, very nasty. Again, I cant tell you what any of those wires do. You'd need to study the R34 wiring diagram (if you can find one that shows the door module). I don't think I have any. I'd have to study the R32 diagram to start to understand what mine is doing, and again, even though I've had a problem with mine for the last 25 years (where it locks the passenger door when the driver's window reaches top or bottom of travel) I'm just not interested enough to try to to work it out. So long as it's not burning down, it's fine with me. Here's the R32 GTR diagram, which, confusingly, has rear door lock actuators and window motors on it!! As you can see, unless you understand the functions of the door lock timer and the power window amplifier, you'll never be able to work out how it works just from the diagram. I don't imagine that the R34 one is any better. Hopefully an R34 aware bod can help. FWIW, the two wires that are cut and joined look like they are both power supply - so hopefully it is not fatal to join them. The 10V you measured on the cut off free end of one of them is concerning. You'd expect 12V, and it might be the reason for the bodge job joining them together.
    • harambe34
      Does anyone know whats happening with harness on drivers door?

      By harambe34 · Posted

      Oops my bad, here you go .
×
×
  • Create New...