Jump to content
SAU Community

Recommended Posts

So this is probably a weird one:

I have a V35 (350GT) 2005 - one of the dashboard back-lights, behind the odometer has died or has dimmed, the back-light for the dashboard clock only reliably works/comes on when the headlight sensors determine it's nighttime outside and dim the dashboard/gauge lights, my passenger side interior light only comes on sometimes when I open the doors AND the bloody fuel gauge doesn't work properly (sometimes it reads it's half-full and then suddenly as I drive it points to being full. Ohhhh and my vents will sometimes blow warm air, even when set to the lowest temp - other days it will be fine. (not because of the engine being warm or cold or it being a hot day etc)

Now I'm completely uninformed about the intricacies of cars, but i feel some, if not all, of these issues are connected because; as I drive to work, sometimes in the cold/damp mornings, my clock will be lit up and working and so will the fuel gauge. But a few hours later when I go to get food, back to square one! 

So I come here to ask for advice - I don't think it's a the actual fuel gauge itself because of how it all seems to happen together. Drawing on my radio technician background, it all feels like something to do with fuses or earthing issues, but I wanted to see what you guys think first.

Thanks

Link to comment
https://www.sau.com.au/forums/topic/477285-electrics-issuefuses/
Share on other sites

42 minutes ago, GTSBoy said:

Give all the likely fuses a wiggle. Pull 'em out put 'em back in. I have one circuit on my car (that powers the radio etc) that needs this every couple of years.

But I would warrant that it's more likely an earth problem.

Thanks so much for the reply. Can I ask, is there a particular place I look at to address an earth issue? 

Sadly, it would probably be behind/under the dash. You need to look at the wiring diagrams to see where there are earth points "close" to the instrument cluster and other devices in that area. Then you can pursue the wiring from those things back towards the various earth points on the steelwork behind/under the dash area.

Keep in mind that sometimes the earths are not actually where you might expect, and might, for example, be out near the sensing devices (like maybe the fuel sender). It is more likely that you will have dud earths out in the open/wet areas of the car or where f**kfisted previous owners could have done something stupid than behind the dash. But you can't exclude the possibility that someone has damaged something behind the dash either.

Edited by GTSBoy

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If you're really considering leaving it, a great question to ask is, is the magnet going to stick to the sump? The answer to the above is the same answer towards if I'd have any level of comfort leaving it... Personally, based on the cost of a motor if the magnet were to cause damage, I'd be fishing it out either way. Use the methods in here. It fit in through the plug hole, it'll come out.   PS, get a small actuatable claw for a bore scope. OR if you know a vet, they have really cool controllable scopes with hooks on the end. Supposedly they're like playing a video game. Ask if they can acquire you one of their scopes... Engine oil after all is just a different type of lube right? Will only make it easier on the next dog or cat...
    • All other (Boolean) logic functions though, are just built on those blocks above. Which does give you a lot of functionality in logic. It is basing that on using thresholds with analogue signals like GTS alluded to.   Not having things like timers will make it less useful for some of the ramp up logic you'd want, and again, on Haltecs capacity specifically, I'm not across anymore what you can / can't do with different tables.   I'm assuming, with your logic you want to implement, not only do you want your timing safeties, you're wanting to be able to derive the duty cycle for your solenoid, to maintain I'm assuming 175PSi? Or are you using a standalone WMI controller to maintain the DC correct, and you just want the Haltech working out which fuelling maps you should be on?
    • It doesn't seem to follow revs. Oddly it seems to follow TPS a little bit from what I can see, but with some delay a bit. IE end of the graph, when he lets off throttle fully, pressure drops a lot, then slowly builds back up, but rpm is on a nice cruisey drop off. I do agree though, it seems very electrically.
    • I just try to entirely stay away from ladder now unless it's something basic maintained by electricians. Even then and to your point, it mostly ends up being blocks I wrote in structured text.  PLC's are slowly going towards C, C++ and C#. I just wish Allen-Bradley would jump on the bandwagon. 
    • All of them are missing. You do not get much done with just AND, OR and NOT unfortunately. Ecumaster for example has a text based editor with at least 60+ math and logic instructions. 
×
×
  • Create New...