Jump to content
SAU Community

Recommended Posts

Hey guys,

The alternator on my RB20e in my A31 took a crap on me.  My buddy has a spare RB20DET one.  Will it swap over or are we going to end up wasting a few hours to try it to see.  Either way, I'll end up taking the old one out to rebuild it if necessary but I'd rather spend the few hours getting it down to a place to rebuild it rather than finding out the hard way the RB20DET one doesn't fit.

Thanks!

Dustin

Edited by dj8684
Link to comment
https://www.sau.com.au/forums/topic/477394-will-rb20det-alternator-fit-rb20e/
Share on other sites

I can't see any reason why not. The brackets all bolt to the block, no involvement with the head, and the block is the same. The drive belt arrangements on the front should all be same same. Nissan didn't use different shit between different chassis if they could avoid it, let alone on the same basic engine in the same car.

  • Like 1

Nice!  Well, that certainly gives some encouragement! We're gonna test it out today and I'll share my progress either way.  I know that the alternators have different part numbers from when I looked them up but then again, a lot of parts do even though they're interchangeable.  Let's see what happens!

So... I can CONFIRM that the RB25DET S2 alternator fits on the RB20e SOHC motor.  Everything was plug and play.  The RB25 one is a bit beefier which is nice so it should provide a little more juice.  The only thing I had to do was buy a slightly larger belt as the one for the RB20e was just a hair too small.

  • Like 2
1 hour ago, dj8684 said:

So... I can CONFIRM that the RB25DET S2 alternator fits on the RB20e SOHC motor.  Everything was plug and play.  The RB25 one is a bit beefier which is nice so it should provide a little more juice.  The only thing I had to do was buy a slightly larger belt as the one for the RB20e was just a hair too small.

Good work reporting results, threads with no outcome make baby jesus sad

  • Like 2
  • Haha 1

hahaha true dat.  I'm actually starting to document all the stuff little by little on my YouTube channel.  I'm gonna start a build thread on here and post the links as a I go.  Sadly, I couldn't film the process on this one because I had to do it in my dark parking garage BUT now that it runs, I can actually take it out in the Sun and start the builds from there.  Here's the build intro vid if you wanna check it out:

 

  • 1 year later...

Hey there,bringing back this forum

I have a c34 laurel with a RB20e and the alternator crapped out a couple weeks back. I managed to score a reconditioned RB25DET alternator out of an R33 which fit directly in etc, However it somehow looks misaligned to me. This may have been because i swapped over the RB20e alternator pulley onto the RB25DET alternator.

@dj8684 Did you just install the RB25DET alternator and RB25DET pulley and just get a bigger belt? Cheers.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • EDIT: Just a little info what my tranny is "doing" :   For the long time the trans do this "bad" sound:https://www.youtube.com/watch?v=qs_iTXgDt40 It is literally the same sound and same symptoms(when i push the clutch it quites down) So is it really the shaft bearing?   Also:  i found this on forums: The RB20 and SR20 boxes are nearly indentical inside (rb20 has longer mainshaft)and suffer badly from bearing and selector failures when driven hard   The bearing is true and selector failure kinda too...it is "harder" to get into gears specialy when i drive a little bit hard...
    • We will review wtf is going on, but if you made any donations let me know and i will follow it up with the admins
    • See, that button sounds like perfection Duncan! My eyes really don't like light shining at them from a dash when I'm driving. Being part red colourblind, I've found for most cars that I can change colours on, I set everything to red, so my eyes see the elast amount of colour! I miss normal gauges in cars
    • bro, knowing the Japanese in  the 90's, i wouldn't be surprised if they shared components across their model lineup.
    • Maaaan so many "little" things  i rly hope my old RB20 would be "ok" and not too bad. I try to learn what and what not do i need. I look at crossmember at it looks different...even parts numbers are different. Wiring and all that i rly do not know...yeah someone mentioned the speedo thing. On that yoke clip. I rly do not know what can and cant be done "custom" so that is why iam asking to know and not be suprised 🙂  I know what it looks like  
×
×
  • Create New...