Jump to content
SAU Community

CAS question

33Reaper

By 33Reaper,
in General Maintenance

 Share

Recommended Posts

33Reaper Rookie

33Reaper

Posted
Posted

Hi im not sure where this post is suppose to be ill apologise in advance my r33 series 1 was making noise from the cover has done 120ks also had markings on the CAS with paper mate ive taken off to see what is going on and i have seen the lower cover is loose on the bottom left side rubbing is there a way taking the bottom cover off without a headache ? thank you

Link to comment
https://www.sau.com.au/forums/topic/478279-cas-question/
Share on other sites
33Reaper Rookie

33Reaper

Posted
  • Author
Posted (edited)

also now i can hear the noise less but can see what it is doing it looks like the pulley that has the CAS on it has little residue / particles of steel flickering from the pulley like its grazing some steel? over tensioned? shit job from previous owner?

Edited by 33Reaper
Link to comment
https://www.sau.com.au/forums/topic/478279-cas-question/#findComment-7913396
Share on other sites
tridentt150v Grand Master

tridentt150v

Posted
Posted

Sounds like your covers are loose and rubbing on the cam wheel?.  The rubber locators on the bolts perish and fall off then the cover doesn't tighten up when you re install.  You have to get new rubbers or make up some rubber washers.

To get the lower cover off you need to take the top one off first.  But first try working around both covers and see where the bolt/rubber locations are and try tightening them or replacing the rubbers without taking them off.  Might save you a few hours if it works.

If you do have to take them off, check when your timing belt was last changed etc…..if its due then you can order a kit with pulleys and belt etc and do them at the same time - while you have the covers off.  While your there check the water pump for leaks etc...might have to replace it as well? Also the cam oil seals and maybe lower seal? 

Link to comment
https://www.sau.com.au/forums/topic/478279-cas-question/#findComment-7913406
Share on other sites
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Sean'O
      3D printing fun

      By Sean'O · Posted

      Howdy friends, So another weird one today, I was looking into replacing some broken clips holding the front grille for the R32 GTR (part number 01553-03831), and noticed the brackets which are supposed to hold the grille in place were also missing 😑. I do recall seeing this issue many years ago, but didn't fix it at the time. A quick look on eBay and I was able to find the genuine brackets, along with all the screws which suited the headlights (part numbers 26042-08U05,26092-08U05). Happy days!....  Once they arrived however there was an extra nut in the packaging which implied that there should also be a bolt or a stud, and sure enough, after a bit of searching I found this thread from 2013, and @Ants clearly shows a stud should be present. Reading around a bit more, it's possible the headlights on my car are the "povo pack" headlights as mentioned by @funkymonkey in this thread way back in 2008. This could explain why the studs are missing on my set of headlights. Looking at the headlight diagram I wasn't able to see a suitable part number for the stud itself. The headlight did indeed have a recess that looked like it would accept a stud, but interestingly no thread or anything obvious how the stud would be affixed to the headlight, I suspect it may have been glued in, press fit, or melted into the plastic at the factory. Another member may be able to clarify if they happen to have a genuine set of N1 headlamps. The only thing we have to work with within the recess is a keyway which likely is there to prevent the stud from rotating within the recess. In any case, back to 3D printing, I put together a model which acts like a pug with a friction fit inside this recess, making use of the keyway so it doesn't rotate while tightening a bolt. Printing in TPU will allow it to slightly swell making a nice snug fit without cracking the part. I've designed the adaptor it to accept an 20 mm M6 bolt (stainless with a cap head in my case), as opposed to the standard M5 stud and I made use of the standard galvanised split washer that came with the genuine brackets from Nissan. Once the bolt and screws were all in place, giving the bracket a gentle shake gave the classic "shaking the car" feeling, very solid, which gives me confidence this is going to be able to hold on much better than the janky solution which seems to have been here for the past decade or so. Overall I'm really pleased with how this turned out and maybe there are more people out there running these headlights without a centre stud at all! Link to the freely available model on Printables: Click here Regards, Sean  
    • GabsReDeal
      R32 GTS (RB20DE) clogged cat

      By GabsReDeal · Posted

      Hey everyone, This is my first post apart of the introduction. I tried searching a bit on the forum but couldn't really get a straight answer. I got the car to my mechanic as I felt it being weak. It seems that it was missing on two cylinders due to the injectors. I had all my injectors clean and the car runs much better. The mechanic also confirmed my suspicions that the cat is clogged and needs to be tackled asap. The cat rattles a bit and the hot exhaust warning frequently lights up when driving after getting the injectors clean. In my introduction I was asked about what modification I might be interested in and mentioned a cat delete. From what I was told, this is not really beneficial on the RB20DE and there are more cons than pros.  Could perhaps anyone give some suggestions on what the best course of action would be since the current cat is toast and needs to be removed/replaced anyway? I can also sometimes smell a strong smell of fuel, but I'm not sure if this is related.
    • Milkmun
      NC MX5

      By Milkmun · Posted

      Hope the cans went down well at least 
    • Milkmun
      Neil's R33 Gts-t Build

      By Milkmun · Posted

      255 can't go wrong with the price.
    • Kinkstaah
      Neil's R33 Gts-t Build

      By Kinkstaah · Posted

      When I was replacing my pump due to being stranded in the wrong state, I went with the Deatschwerks 320lph kit. It is a direct plug in to the stock wires, harness, everything. It comes with a plug... but you can plug the OEM plug directly into this thing. https://justjap.com/products/deatschwerks-dw300-fuel-pump-nissan-s13-silvia-r32-r33-r34-skyline-c34-stagea?currency=AUD Downside: Won't actually flow that much on boost if you want to push it on E85, but it's comparable to the 040/255 etc. Little more actually.
×
×
  • Create New...