Jump to content
SAU Community

RB25DET gearbox rebuild issue, 4th gear locked

hardsteppa
 Share

Recommended Posts

hardsteppa Grand Master

hardsteppa

Posted
Posted

so have finally finished putting the box back together, but now it's all assembled and housings are back on, I have an issue where it's locked in 4th gear constantly and will only turn by hand in 4th or neutral, but the whole shaft turns in neutral, not just one end. It selects all gears fine but won't turn in any other gear. Before I put the housings back on I confirmed all gears select and shift as they should and all turn accordingly with the gear selected, but once the front housing is back on, it locks up. I stripped it back down to make sure hadn't made any error in reassembly and the syncros bearings etc all sitting as they should, and everything was fine but as soon as the front housing went back on, it locks up again. I haven't filled it with any fluid yet so I'm thinking maybe is there too much friction on the 4th syncro when it's dry? (although I did put a little grease on it on it when reassembling for the 2nd time, hasn't made any difference). 

This box was a 2nd-hander off gumtree so I never actually used it myself to know of any issue with it prior. At a standstill with it now so, ideas are welcome.

BK Grand Master

BK

Posted
Posted

Definitely sounds like 4th synchro is not letting go. Usually some oil squirted there fixes it and sounds like you're onto it being a dry problem. Have seen that happen on our boxes, and have had calls about boxes doing that with new sychros we have supplied.

hardsteppa Grand Master

hardsteppa

Posted
  • Author
Posted

Thank you once again for your help. I was going to give it a part-fill before putting it back in the car and give it a thorough turning over to get oil over everything; hopefull does the trick.

BK Grand Master

BK

Posted
Posted

Hey mate on a more serious note, please tell me you used Threebond 1207C sealant on the bottom three front cover bolts and NOT threadlocker (or even worse nothing) ? Had to pull my dog box out of my 32 on the weekend, after the one box we didn't do ourselves and outsourced pissed oil out of the front cover. Noticed a slight drip under bellhousing and though fcuk, they didn't did they ? Found this as expected...

IMG_1947.jpg

WP_20191012_15_50_48_Pro.jpg

WP_20191012_15_49_22_Pro.jpg

WP_20191012_15_49_12_Pro.jpg

WP_20191012_16_58_53_Pro.jpg

WP_20191012_17_16_51_Pro.jpgPretty annoying to pull a box out to reseal 3 bolts, but said transmission specialist was very apologetic after I showed him the stuff up. We didn't check front cover before install, but why would we ? It was done by a very experienced transmission specialist that knows what they're doing, so it can and does happen to anyone. It is in the Nissan manual after all so no excuse....

Check, check, check

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • OakvilleGTR
      Turn signal wiring question

      By OakvilleGTR · Posted

      Good morning all, Bit of a random question but figured I’d finally throw it out after wondering for a long while. Before I start, I'm hoping to do this purely out of personal preference. I think it would look better at night, and don't mind at all spending a few hours and dollars to get it done. I've copied this from a non-Skyline specific forum, so I apologize for the explanation of our headlight switch setup that we all know. Here we go: Zero lights (switch off) Parking lights (switch position 1) being a rectangular marker on the outside of the housing, my low beam being the projector in the centre (position 2), and a high beam triggered by my turn signal stalk. Most North American cars I’ve owned of this era have power to the amber corner (turning indicator) light as part of the first switch (parking lights). I’d love to have these amber corners receive power when the headlights and parking lights are on (headlight switch), yet still blink when using the turn signal which is of course a separate switch. Hopefully I’ve explained my question correctly. Is anyone aware of a way in which I might be able to achieve this? Thanks in advance
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      My heads are cathedral port! It's likely possible, but I don't want to add any extra moving parts (I know they don't move) between the heads, manifolds, etc. It will also affect how injectors/fuel rails etc sit and I don't really know if it would change how the FAST manifold goes/sits/fits. I have the LS6 steam pipes already as I have a very late LS1 block so it should be fine. I couldn't find anyone who had ever actually used one for this purpose, it seems 100% of people grind the water pump. The thermal spacers are 12mm and are half way to the cost of the newer water pump anyhow... so if it comes to that I suppose I'd rather buy a new pump. The bearing in the pump I do have is a little.. clunky, but it hasn't done that much time and I never noticed it when the car was together in the past few years, so..
    • sonicii
      Lower A arm Skyline v35

      By sonicii · Posted

      The bushing has failed, not all that uncommon for a car of this age.  Any mechanic should be able to push in a new bushing for you, or you can probably buy the entire lower control arm, complete with bushes.
    • The Bogan
      Mistakes were made, my R34 Story

      By The Bogan · Posted

      Could you not use "thermal" spacers to give the clearance, like the ones I used between the blower and head? That raised the manifold height by around 10-15mm Albeit the ones I used were for cathedral ports, but I assume they have similar for rectangular ports????
    • Red Sky II
      Looking for autoelectrician in Perth who can do the OEM to double din stereo upgrade.

      By Red Sky II · Posted

      Thanks Paul I reached out to Autotainment but they no longer work on JDM cars as the guy who used to do the work moved on and is no longer doing that kind of work. I am talking with Level Up Audio though.
×
×
  • Create New...