Jump to content
SAU Community

Recommended Posts

Hello Everyone, 

I have:
New Mishimoto Radiator
New Mishimoto Electric and Shroud (came with ONE fan)... wired professionally from a ignition source from the Fuse Box and wired with its own fuse and relay. 
New Mishimoto Colder range Thermostat

and YET! it still overheats in 10 mins on the street with regular driving either and day 29 degrees C or Night 27 degrees C

The Dash Board's Temperature gauge will slowly climb to about 75% to the top and then at a certain point will start slowing jumping up and down and up and down from 75% to 95% (overheating).

I was told that: 
-The single electric fan is ass and cant cool the radiator so go back to the clutch fan and shroud.
-The Thermostat is faulty/not working. replace it and one guy even said dont even use one. I live in the Caribbean by the way... 
-When switching over to a GReddy Forward Facing Plenum, the coolant temp sensor could have been damaged/stop working. But the engine bay is HOT!

 

Link to comment
https://www.sau.com.au/forums/topic/479119-r34-rb25neo-always-overheating-help/
Share on other sites

First of all why did you change the radiator? If it was ok before then revert to the stock set up and sell the Mishimoto.

While you have it apart remove the thermostat and back flush the block.

Fit a stock thermostat. Then test the new one to see if it was faulty. Even if it is not, a low temp thermostat just opens earlier. Once open it has no effect what so ever on the running temps of the engine.

57 minutes ago, KiwiRS4T said:

First of all why did you change the radiator? If it was ok before then revert to the stock set up and sell the Mishimoto.

While you have it apart remove the thermostat and back flush the block.

Fit a stock thermostat. Then test the new one to see if it was faulty. Even if it is not, a low temp thermostat just opens earlier. Once open it has no effect what so ever on the running temps of the engine.

Well i was obviously looking for better cooling capabilities out of this upgraded set up.... I have a feeling it may be the Thermostat possibly not opening? i am not to sure, how could you find out if a thermostat is doing its job?

Several things can contribute to this, however since you have recently replaced the radiator:

  1. Ensure ALL the air has been bled out of the coolant system, there is a 10mm hex head bolt near the front of the plenum for this purpose.
  2. You did not mention if the water pump was replaced, as per the manual this should be done every 100,000 km at the same time as the CAM belt.
  3. If you have access to diagnostic software and equipment for this car check the O2 sensor, if this is faulty your engine may run lean to 'compensate' for a bad reading, the leaner the fuel mix the hotter it will get.
5 minutes ago, Dil-Dog said:

Well i was obviously looking for better cooling capabilities out of this upgraded set up.... I have a feeling it may be the Thermostat possibly not opening? i am not to sure, how could you find out if a thermostat is doing its job?

To test a thermostat, remove it from the vehicle clean it, put it in a pot of cold water with a temperature gauge and slowly heat it on a stove. It should reach its maximum valve travel at the temperature it is rated for and stop moving, if it does not stop moving or does not fully open it needs to be replaced.

To find out the specs look up the part number of the manufacturers website, there should be a datasheet indicating it's travel values

  • Like 1

It is also worth noting that generally speaking, the cooling system for R chassis is actually pretty decent. Even if you're doing 30 min track abuse sessions the stock fan/shroud does the job, let alone street driving. I know it's already been suggested but getting back to a known good setup is recommended.

To be fair a decent thermo setup shouldn't cause issues for street driving either.. but its safe to say the stock Nissan Fan/Shroud/Radiator/Simple Rad upgrade that bolts to OEM positions/gear won't.

Mishimoto fans are junk, throw it into the bin.

Use the stock 250kW (or whatever your motor is making) fan you have, if you don't have it go buy a SPAL electric fan to replace that Mishimoto junk.

  • Thanks 1

UPDATE: 

For those who care and for anyone who may be able to learn and get help from this post for their projects... the problem the god awful mishimoto electric fan.
 

Its sucks booty butt cheeks and is better off being a fan for a computer or somthing... the stock clutch fan is honestly 10 times better in terms of air flow.

  • Like 2
1 hour ago, GTSBoy said:

Yes. But shit fan or not, it still shouldn't overheat while just driving around. Low power + moving car should be enough air through the radiator.

Also shit radiator.

Not in city traffic though, especially with a FMIC in front.

And like I said earlier Mishimoto fans are junk, also have said it in the past too but people get butt hurt and get all defensive lol

  • 3 months later...

Mishimoto? sounds like some Mitsubishi after market brand....  aint none of that going on my Nissan.

+1 for stocko clutch fan.

 

only reason to change a clutch fan is if ur cold startin an e-series falcon and setting off in the morning.

(falcon sounds like ur doing 300km/hr......people look out their windows.... and see u...……... doing 3)

As I've read so far most all would rather stay with the factory clutch fan....... buuuut if one was going to take the time to wire in a set of electric fans. Which ones should be avoided or not even considered( like said mishimoto)

5 hours ago, kowalatea said:

As I've read so far most all would rather stay with the factory clutch fan....... buuuut if one was going to take the time to wire in a set of electric fans. Which ones should be avoided or not even considered( like said mishimoto)

All of them.

  • Haha 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Haha yea it's a bit of a weird setup at the moment, just wanted to make sure I sorted out any headaches before dyno day. At the moment I've changed the exhaust manifold, turbo and downpipe, 460lph fuel pump and rising rate reg as well as the previously mentioned headstuds and gasket. The nistune was already mapped for the car as it was and drove around for a few months no worries. The plan is to run flex fuel hence the big pump, which I've wired direct to the battery through a relay to avoid voltage issues.
    • Um. Was the ECU the same as the one previously there? I know R33's needed R32 GTST ECU's or other tomfoolery to run Nistune. This is such a wild setup. Most people would plumb in the turbo then not drive the car (i.e tow it to a tuner). What's actually changed since it last ran?
    • I'm a bit stuck with this one fellas, I recently decided to undertake a turbo conversion on my GTS-4, ended up pulling the motor to replace all the seals and do an mls head gasket and arp head studs while I was at it. Everything has gone according to plan, no oil or coolant leaks, compression checked out, and decided to give it a test before I book it in for a tune As it stands right now, the turbo only has oil lines plumbed so that I don't put boost into my untuned engine, and I'm using the factory GTS-T crossover pipe with a maf and poddy as a temporary intake. The car starts with relative ease and idles amazingly, however as the title suggests it really doesn't want to rev up, runs very smooth but almost feels choked out and unresponsive to the throttle, almost like it's running lean or something? I've triple checked my vacuum lines and timing with a timing light, injectors haven't been touched as of yet to avoid flooding the engine and worked perfectly beforehand, new plugs and coilpacks, I've even unbolted the cat just to see if it spontaneously collapsed, no dice The car currently has a nistune r32 gtst ecu installed so I have no way to check for fault codes. At this point I'm a bit stumped. Is this normal behaviour for a car with a turbo bolted onto the exhaust going nowhere? I'd imagine the turbo wouldn't cause this much restriction in the exhaust without the boost going through the intake. Any ideas? If necessary I can link a video of how it responds to full throttle while in neutral.  
    • Insert tab A into slot B?
    • Instructions seem simple enough to understand.....
×
×
  • Create New...