Jump to content
SAU Community

Recommended Posts

Hi guys,

i'm going to get off my stock turbo an put on a Garrett GTX3076.

Other mods like FMIC, 600 cc injectors, link g4+, DW fuelpump etc. will be or were already added.

So I took the head off and got it machined to have an even surface. I've cleaned the block with a razorblade to get off the rest of the oem headgasket. The machine shop took off 0.16 mm from the head to get an even surface. The oem gasket thickness is 1.2 mm as I've read, so if I add the 0.16 mm the replacement has to be at least 1.36 mm. Correct?

As I am from Germany, i've searched for a metal headgasket in the local online shops but just found 1.2 or 1.5 mm but no 1.4 or 1.3.

 

So which thickness would you recommend? Or would the oem Nissan gasket be good enough for my setup, keeping in mind that the block was only cleaned by hand?

Ok, thnks for the info. Is this the correct one? https://www.tj-partshop.com/products/13009-Tomei_Headgasket_Zylinderkopfdichtung_Nissan_RB25DET

It is available with 1.2 or 1.5 mm. Which thickness would be the right choice?

The Tomei compression rate calculator says that the oem gasket thckness is 1.1 mm and the compression is 8.97.

With the 1.2 mm gasket the compression rate would be 9.03 and with the 1.5 mm it would be 8.76. 

1 hour ago, GTSBoy said:

How can a thicker gasket increase compression ratio?

I've clculated the compression ratio value for the 1.2 mm including the 0.16 mm of material that the machine shop removed from the head.

When I use the 1.2 mm gasket it will be the same as 1.04 mm gasket with the cylinder head before machining it.

11 hours ago, Finn_GT-T said:

Ok, thnks for the info. Is this the correct one? https://www.tj-partshop.com/products/13009-Tomei_Headgasket_Zylinderkopfdichtung_Nissan_RB25DET

It is available with 1.2 or 1.5 mm. Which thickness would be the right choice?

get 1.2mm

It's 2019 not 1979 where we have shitty ECUs :) 

2 hours ago, AngryRB said:

Just get a stock RB25 head gasket and ARP studs.. 

 

You know a Tomei or Nitto head gasket is much more? Not to mention it's better than the stock composite head gasket.

 

1 hour ago, Dose Pipe Sutututu said:

You know a Tomei or Nitto head gasket is much more? Not to mention it's better than the stock composite head gasket.

 

I know my RB3025 has no issues at 350kw, is a simple oem RB26 gasket that was very reasonable cost from Kudos with ARP studs.. 

If the block surface isnt perfect then it could leak and after pulling engines out a few times recently im over that bullshit so id advice OP to keep it simple.

 

1 minute ago, AngryRB said:

I know my RB3025 has no issues at 350kw, is a simple oem RB26 gasket that was very reasonable cost from Kudos with ARP studs.. 

If the block surface isnt perfect then it could leak and after pulling engines out a few times recently im over that bullshit so id advice OP to keep it simple.

 

You clearly missed what I said earlier about Tomei or Nitto head gaskets ?

How I see it is you've spent that money/time to take off the head and skim it, purchased a larger turbo and going to run ARP studs (over the factory head bolts), then what's an extra $200 to the equation? not much.

Not to mention the Nitto OR Tomei headgasket will seal better and also will withstand the punishment as it's o-ringed. Every car workshop does the same thing. I also got told this advice from both MRC and Billtech (both reputable RB workshops).

I would only advise going with a Cometic or similar style headgasket if your block is prepped.

12 minutes ago, GTSBoy said:

Or perhaps the correct grammar version where you advise against it?

FUUARK - this is proof Asian Males cannot multitask, was typing out an e-mail to a vendor at the same time about "advising" shit too LOLOLOL

(have edited the previous failed post)

Thanks @GTSBoy

 

Thank you all for the replies. This forum is much better than the german equivalent.

ARP studs are already in my garage waiting for me to screw them into the block. I think I'll go for the tomei gasket because of the small extra cost but higher (presumed) reliability compared to the oem gasket.

Will the higher compression ratio be an issue when mapping the link ecu because of the risk of knocking? Keeping in mind that the stock knocksensors will stay in the block.

By the way, what do you think about applying permatex spay gasket to the tomei gasket before assembly? Does it help to get a better sealing, or is it just wasted money?

Edited by Finn_GT-T

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Major thread necro but how bad of a job is it to DIY? Looking at it online it looks like if you reuse your ring and pinion as long as those are in good condition it should be fine to just pull the axles/front cover and replace the diff that way? Or should I be replacing everything and doing preload measurements/gear mesh testing like the factory service manual mentions for the rear diff?
    • in my list I had the R33 GTR as the best Skyline. Infact I had all GTR's (33>34=32), the NSX, the GTO, the 300ZX, the 180SX, the S15 better than the FD RX7. I had the MR2 and the A80 as 'just' better. I also think the DC5R Integra looks better but this is an 01 onwards car. I also think the FC>FD. It's almost like aesthetics are individual! The elements @GTSBoy likes about the FD and dislikes about the 180 are inverse in my eyes. I hate the rear end of the FD and it's weird tail lights that are bulbous and remind me of early hyundai excels. They are not striking, nor iconic, nor retro cool. The GTO has supercar proportions. I maintain these look much better in person (like the NSX) especially with nice wheels and suspension which is mandatory for all cars pretty much. Some (or all) of these you have to see in person to appreciate. You can't write a car off until you see one in the flesh IMO. Like most people we probably just like/dislike cars which represent certain eras of design or design styles in general. I also think the 60's Jag E type looks HORRIBLE, literally disgusting, and the 2000GT is nothing to write home about. FWIW I don't think the Dodge Viper Gen1's have aged very well either. You can probably see where I rate bubbly coupes like the FD. I know we're straying now but the C4 and C5 absolutely murder the Viper in the looks department as time goes on, for my eyes. Wouldn't surprise me if people who love the FD, also love the MX5, Dodge Viper, Jag E Type, etc etc.
    • I used to hate R31s, and any of the other Nissans that led up to it, and any of the Toyotas with similar styling, because of the boxiness. They were, and remain, childish, simplistic, and generally awful. I appreciate R31s a lot more now, but only the JDM 2 door. The ADM 4 door (and any other 4 door, even if they are unique compared to our local one) can eat a bowl of dicks. The Aussie R31 is also forever tarnished by their association with stereotypical bong clutching Aussie R31 owners of the 90s and early 2000s. I think the Nissans of the 70s (other than 120Y/180B/200B) are far superior looking to the 80s cars. The 240K era Skylines are boss. The same is broadly true of Toyotas. Hondas don't ever register in my thinking, from any era. Mitsus are all horrid shitboxen in any era, and so also don't register. Subarus are always awful, ditto. Daihatsus and Suzukis also don't generally register. They are all invisible. I think the SW20 MR2 looks fiddly. The 3000GT/GTO is like that but way worse. Too many silly plastic barnacles and fiddly gimmicks ruined what could have been a really nice base shape. Kinda-sorta looks like a big heavy ST165 Celica coupe (and I'm not sure if that's a good thing or a bad thing). I think the 180SX is dreadfully bland. It's not bad looking. But it has no excitement to it at all. It's just a liftback coupe thing with no interest in its lines, and bad graphical elements (ie wide expanses of taillight plastic on the rear garnish). The S13 Silvia is a little better - getting closer to R32 shapes. But still....bland. S14? Nope. Don't love it. S15...a little better. Probably a lot better, actually. Benefits from not being like a shrunk in the wash R34 (where the S13 was a shrunk in the wash R32 and the S14 looked like a Pulsar or something else from the stable on Nissan mid 90s horrors). The Z32 was hot as f**k when it came out but hasn't aged as well as the A80. Keep in mind that I think the R33 is the most disgusting looking thing - and out of all the previous cars mentioned is objectively closest to my precious R32. It's just....real bad, almost everywhere you look. And that is down to the majority of what was designed in the 90s being shit. All Nissans from that era look like shit. Most other brands ditto. In that context, the FD absolutely stands out as being by far the best looking car, for reasons already discussed. Going behind the aesthetics, the suspension alone makes it better than almost any other car.  
    • If they just called it the "Mazda Tiffany", it would have been spot on.
    • Yup but for me its the HR ! Cut my teeth on the old holden 6s in the day ! And here's me thinking in the day it was also the 300ZX and the Mitsubishi GT3000 ! All, as well had good lines, but always seemed to need finishing off, style wise.
×
×
  • Create New...