Jump to content
SAU Community

R32 GTS-T - Rethreading and Suspension brackets

32_love

By 32_love,
in General Maintenance

 Share

Recommended Posts

32_love Collaborator

32_love

Posted
Posted

Hey guys,

 

I've stuffed up again. While doing, what should have been, a simple front swaybar installation I managed to round the thread for one of the D-bracket bolts. (see pic)

I'm now trying to re-thread the bugger but it's in a very difficult spot. I was just wondering if anyone can confirm for me that it's ok to remove this whole bracket that the castor rods mount to so that I will have enough room to spin the die with a hand tool?

or am I going at this the complete wrong way?

Any help/tips would be appreciated.

 

Note: I'm 99% certain that this bolt is an M10 x 1.25 but if you happen to know better please let me know.

IMG_4604.thumb.jpg.1e0b6c51a70c196bb6d5386d5d237e80.jpg

 

Thanks,

 

Aaron

hardsteppa Grand Master

hardsteppa

Posted
Posted

You can remove that bracket no problem, it just unbolts - make sure you unbolt ps line too o' course. Should be able to overdrill n helicoil it if rethreading it doesn't work.

  • Like 1
GTSBoy Grand Master

GTSBoy

Posted
Posted

I'm not sure I understand. You've f**ked the thread on a stud, not a bolt. I'm pretty sure that that stud is welded into that bracket and you are not going to gain any more clearance to turn a tap on it removed than you have wit it where it is. The correct fix here would be to remove the whole lot and grind back whatever welds locate that stud (probably on the top side) and get it out and weld in a replacement.

  • Like 1
  • 3 weeks later...
32_love Collaborator

32_love

Posted
  • Author
Posted

Just to finish off this post.

As per usual, GTSBoy was correct. The stud was welded to the bracket.

I was able to remove the bracket as per HardSteppa's comment.

The fix ended up being Craig from Threadtech coming out to have a look (3 days before xmas) and fixing it with a hex headed die and a wrench in all of 10 minutes.

 

Really feel like an idiot after all this, but glad to have the car back down on the ground and secure.

Ben C34 Grand Master

Ben C34

Posted
Posted
5 hours ago, 32_love said:

Just to finish off this post.

As per usual, GTSBoy was correct. The stud was welded to the bracket.

I was able to remove the bracket as per HardSteppa's comment.

The fix ended up being Craig from Threadtech coming out to have a look (3 days before xmas) and fixing it with a hex headed die and a wrench in all of 10 minutes.

 

Really feel like an idiot after all this, but glad to have the car back down on the ground and secure.

thanks for updating.

he would have loved that job. doesn't get any easier than that! :)

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      Potential MAP Reference Point

      By joshuaho96 · Posted

      Isn't there a fitting on the back of the balance tube? That's what the OEM boost gauge uses.
    • GTSBoy
      Potential MAP Reference Point

      By GTSBoy · Posted

      Getting a decent signal from all 6 throats is a challenge. I don't know for sure, but I suspect that the stock balance tube is not ideal for it. I have done it on an ALFA 4 cylinder (about 35 years ago, so don't ask for too many details). We drilled 4x holes in the manifold runners, put in some fittings and ran hoses to a decent sized (I think it was about 20mm diameter) pipe that ran the length of the inlet manifold. So, it was quite a decent volume. There is a "tuning" balance to be found between the volume of the common plenum on such a thing and the diameter of the pipes running from it to the runners. You need the volume to be large enough to damp out the sharp spikes in pressure signal you get as each runner gets sucked on by its cylinder, but not so large that it becomes too slow to respond to actual changes in MAP. And you need the hoses to be small enough to transmit the signal quickly, but not so small that they delay the signal. You might have to have more than one go at it, if there isn't any actual success based wisdom to be had here. Hopefully there is. Anyway, I would not do it on only a couple of cylinders. I would also not care about "permanently modifying a part". Just bloody drill holes and make stuff better. There is nothing sacred about any GTR unless it is a genuine museum piece that you shouldn't be modifying at all anyway.
    • MBS206
      NC MX5

      By MBS206 · Posted

      He's still joining you, he's just delayed it and won't have the fulleh sick ITBs...
    • Kinkstaah
      R34 GTT front hood lip

      By Kinkstaah · Posted

      The strange thing is this is a URAS front bumper (or clone of it). The bumper actually does not sit flush with the GTT hood - You need the addon to make the hood 'long' enough to reach the bumper. I have no idea why they didn't incorporate this piece into the bumper itself.. instead of sticking it to the hood instead.
    • AdiR34
      R34 GTT front hood lip

      By AdiR34 · Posted

      Another thought on this OLD topic: When you paint your bonnet lip, leave a small unpainted back lip/line along the back of the lip, where it rests on the bumper. That way, the line in the back is much more prominent than the gaps in the front/under the lip - and it breaks the hood-to-bumper connection at the "correct" place, when comparing to a GTR. I'm gonna do this with mine this week, so stay tuned for pics!
×
×
  • Create New...