Jump to content
SAU Community

Recommended Posts

I just got a R33 and have been working on it just over a month now with a friend. Since received the car has had boost issues whenever it's under throttle. Sometimes the boost gauge doesn't go past 5-7psi with the car sputtering like crazy under acceleration. Other times the boost gauge shoots way past 10psi almost instantaneously. First we checked the compression to find 170-180psi across all 6 cylinders (most were 180). We then removed the plugs, cleaned them, gapped them (0.035-0.040) and re-installed. No difference. We heard an air leak from the intake side when we first got it, so we took off the manifold and replaced all gaskets and hoses. The air leak was gone but the problem persisted. We took out the factory fuel pump and filter, put in a new filter and a 340lph fuel pump. Problem persists. We tried two aftermarket manual boost controllers. We used every vacuum diagram on the web for a R33 boost solenoid (sadly there are literally guides stating that every way to run the hoses is correct). We removed the heat shield to the turbo and could move the wastegate manually, so chances are it isn't stuck. Problem persisted. We then ran a hose directly from the charge pipe (coming off the intercooler to the intake pipe), directly to the wastegate (bypassed the solenoid) which should give us 5-7psi. The problem persists.

When you're driving anywhere below 3psi the car runs like normal. It has a factory ECU with zero codes. Stock turbo, stock intercooler, stock piping. The only aftermarket mods are HKS plugs, Apexi Filter, and downpipe/exhaust. Neither of us has any idea why this car continues overboosting causing a horrible sputter. We appreciate any help this community can offer.

If it's misfiring at 5 psi or so, then it is weak ignition. Your coils are the most likely culprits there.

The boost control issue is not something that will be easy to diagnose across the 'net. Especially if you have had it apart lots. It will be something weird.

Today I hooked up a 5psi source to the wastegate, and it moves just fine.  No idea why it was overboosting.  We checked the fuel pressure and it's a bit higher than it should be, which I've read happens sometimes when you go with a higher lph pump due to the extra fuel being returned to the tank, causing a bit of a pressure buildup.  We took some coilpacks off another RB25DET, swapped them on, and sure enough that was it.  Set the timing and now she runs perfectly!   Thanks for the help :)

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • $170K. I asked one of the guys there as a joke if that price was just for the passenger seat as it was where the price sheet was... he tried really hard to crack a smile 😄 He also mentioned that every single part of the car was inspected and either restored or replaced with a new or as new part, or made from scratch. The interior was incredible, every inch like a new car.
    • Time for a modernisation, throw out the AFM, stock O2s, ECU into the e-waste bin. Rip out the cable throttle, IACV, pedal, etc. into the scrap metal bin. DBW, e-throttle, modern ECU, CANbus wideband, and the thing will drive better than when it left the factory.
    • I agree, don't go trusting those trims. As I said, first step is to put the logger away, and do the basics in diagnosis.   I spend plenty of time with data loggers. I also spend plenty of time teaching "technicians" why they need to stop using their data loggers, and learn real diagnostics.   The amount of data logs I play with would probably blow most people away. I don't just use it to diagnose. I log raw CAN data too, as a nice chunk of my job is reverse engineering what automotive manufacturers are doing.
    • I'm aware, but unless you're actually seeing the voltage the ECU is seeing and you're able to verify the sensors are actually working I find it hard to just trust STFT/LTFT. I will say, logging the ECU comes naturally to me because it's one of the lowest effort methods of diagnosis and I do similar things in my day job all the time. Staring at 20+ charts looking for something that isn't quite right isn't for everyone. NDS1 allows you to log almost everything so that's normally what I do and then sort out the data later. 
    • Silly question, as I bet you've checked already, but the motor turns over by hand yes? I suspect Neil has a spare starter, though if not, I believe I have a spare R33 (or two) starter.
×
×
  • Create New...