Jump to content
SAU Community

Recommended Posts

Hey all

Im in the market now for a R35 GTR

Ive been looking around at the ones in the 2009 era.

What conman things should i look out for?

What problems can i get checked?

I would most probably take it to my tuner to run his eye over to

Link to comment
https://www.sau.com.au/forums/topic/479685-r35-looking-to-buy-questions/
Share on other sites

I think pre 2011 maybe 2010 had some sort of gearbox issue. If its an 09 or early 10 you'd want to know that has been rectified. I assume if you google about it, there should be lots of info as well as merica sue someone, class action, save the kids type posts.

If i was you id be stretching as far as i could to get the newest model with the lowest km as possible. A bloke i worked with had an 09 and its not a case of if but when the gearbox plays up. His went with under 20k km on the clock. He then bought a 12 and now has an 18, both had no issues.

  • Like 1
On 2/4/2020 at 1:42 PM, admS15 said:

I think pre 2011 maybe 2010 had some sort of gearbox issue. If its an 09 or early 10 you'd want to know that has been rectified. I assume if you google about it, there should be lots of info as well as merica sue someone, class action, save the kids type posts.

If i was you id be stretching as far as i could to get the newest model with the lowest km as possible. A bloke i worked with had an 09 and its not a case of if but when the gearbox plays up. His went with under 20k km on the clock. He then bought a 12 and now has an 18, both had no issues.

I'd second this. My old man was looking at one years ago and I remember from my research that you'd at least want an MY10 or plus to avoid the early gearbox issue. If you can stretch the budget, try for as new as possible with best service history.

i went through this same process just recently, unless you find one that's below $75k, i am not sure if it's actually cost effective. there was a decent 09 car that went in 2 days, had all the transmission fixes done, full bolts and tune which is about 650awhp, otherwise i am finding that the facelift model (MY11+) are about the same cost as getting an 09 with low KM but ends up same as an MY11 due to requiring all the fixes to be done.

 

I ended up getting an MY12.

 

 

  • 3 weeks later...
  • 1 month later...

Agree with phillay, if you can find an 09 with all the mods done for a good price, go for it . Otherwise 11 or later when Nissan did the inevitable upgrade. Not sure about the psychology of 35 owners/sellers. Have the pleasure/privilege of running a 32, 34, 35, twin turbo350 and a JDM S15, among others. Always under pressure due space, rego and insurance etc, but when it comes down to it, there is simply no better car to get behind the wheel of. Just a fricking awesome car to drive, and always brings a smile when I touch that start button and hear that rumble! It would be the last to go.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I can't agree. If we hadn't all been brought up with the noise caused by the inefficiency of an ICE, no-one would actually ask for all that. An EV is like any other car, it just goes better. 
    • 2 more things I have to work out Easy one first...can anyone describe how to pull the fuel pump and sender from a 33? I can feel there is some sort of mount and clips but don't have a manual and don't know the trick......if not I'll spend some quality time in the boot witha lighter tomorrow. Second question is harder.  He had changed the upper plenum to a plazmaman but clearly got to a point with the vacuum hoses where he said "f**k it, I'm going inside for a beer" and never came back to that job because it was a mess. Am I right to think that I need: 1. Pre throttle (16mm nipple on inlet) to AAC's main 20mm fitting as the main pre throttle feed 2. ACC has a second 13m outlet joined to that 20mm fitting which I think is the pre throttle air supply for the cold start valve? 3. Cold start valve's outlet fitting then goes to Plenum (to bypass throttle?) There is some adapter on the back of the ACC with 2 fittings (13mm and 10mm), do I run the 10mm through a 1 way valve to the Brake Booster (4) and the 13mm back to a 13mm nipple on the Plenum as the Idle control (5)? 6. Run a 6mm vacuum line from the Turbosmart BOV to the Plenum? 7. Run a 5mm vacuum line from the Fuel Pressure Reg to the Plenum? 8. Run a 5mm vacuum line from the Turbosmart Boost controller to the Plenum? (Wastegate already has a pre turbo pressure source running to the solenoid then the wastegate on the other side of the bay)  Any help appreciated, the GTR is quite different setup and while the Stagea also has FFP it is different again. (And no Dose, I'm not pissing it all off and putting a ethrottle on it....)
    • OK, onto some questions to try and speed up the process a little. Does anyone know what core this Garret is? I know it is a high flowed standard turbo but nothing else about it. Tag says OK 0169J - 446179-5032 Same question for the injectors, I don't know what they flow and ideally can work it out before it hits the dyno, they are a mustard yellow side feed
    • Quick side trip into the engine externals, alternator and PS were in place including tensioned belts, but the PS was dry (my guess is he had the steering rack reco-ed). Filled it up with Transmax Z but it will need more bleeding once the engine is running no doubt. BTW I've said before, I don't know what kind of soft animals you have in the city, but out here they breed the rats tough. I bet they were disappointed when they tasted synthetic ATF.... Coilpacks are Splitfires with a factory loom in reasonable condition. I didn't pull one put I bet the spark plugs are new as its a new engine
    • Onto intake pressure test. I have a Raceworks (damn brand thieves!) pressure test adapter that lets you apply pressure through a standard tyre valve and comes with a pressure gauge.....I just blocked off the other end immediately before the throttle body. Applied 30psi....and the turbo intake immediately popped off with a bang. Sorted that but it was still leaking, turns out there is a pinhole leak at the BOV adapter that I'll have to find a local place to TIG up. I'm sure it makes SFA difference with such a small leak but I want it to be right. Everything else up to the throttle body was good. Also cleaned and oiled the KNX cone filter, and this is the AFM if anyone can identify it (car runs a PowerFC)
×
×
  • Create New...