Finn_GT-T Posted February 10, 2020 Share Posted February 10, 2020 Hi, yesterday I tried to start my GT-T the first time after upgrading to GTX3076 and Link G4+. Well, it failed. What has been modified? Link G4+ GTX3076 int. wastegate Link 3 bar map Tomei headgasket Deatschwerks 600 cc injectors Deatschwerks DW300 Fuelpump Blitz FMIC 3" catback + 3" downpipe + custom turbo elbow Oil gallery restrictor GFB Mach 2 blowoff What was not done, but will come in the near future? Fuel pump rewire to replace the fpcm Link IAT sensor (not wired in) Tomei fuel pressure regulator wastegate actuator (mounting plate missing) boost soleniod not installed because ot the missing wastegate actuator wideband (oem narrowband installed) Modifications to the ECU: R34 GT-T base map stored to ecu configured for link map sensor calibration of the map sensor calibration of the tps deactivated temp3 input (fuel temp - was enabled in base config and causing errorcode) deactivated the iat because of not being installed yet When I turn the key the fuel pump and injectors get highlighted in green, so I think that the ecu activates them. The starter cranks the engine but with no sign of firing it up. Could it be a problem that the iat is diasbled? should i reduce the duty cycle of the injectors? Is there any further config needed that i could check before searching for issues (ignition spark/fuel/etc)? Link to comment https://www.sau.com.au/forums/topic/479735-gt-t-link-g4-first-start-failed/ Share on other sites More sharing options...
GTSBoy Posted February 10, 2020 Share Posted February 10, 2020 Check for issues before posting to the internet for help diagnosing something that is best diagnosed in situ. Link to comment https://www.sau.com.au/forums/topic/479735-gt-t-link-g4-first-start-failed/#findComment-7924593 Share on other sites More sharing options...
Finn_GT-T Posted February 10, 2020 Author Share Posted February 10, 2020 The main question is in my last sentence. I'd like to be sure that it is not a problem caused by wrong parameters in the base map or my config. Link to comment https://www.sau.com.au/forums/topic/479735-gt-t-link-g4-first-start-failed/#findComment-7924594 Share on other sites More sharing options...
Dale FZ1 Posted February 10, 2020 Share Posted February 10, 2020 Link provide an extensive help menu. But you need to go right through the whole tune file, make sure the sensor settings are correct, and calibrated. This includes CAS, TPS, injectors. First time around, you will burn time. But follow their prompts and don't leave out any steps. Physically check connections like CAS, injectors, and coils. It is easy to test fire the injectors and ignition without the engine running, just follow the help menu. If you haven't got IAT wired and functional, you're going to need to work around that one, in case the settings makes the ECU think it's seeing -50 or +140C temps. The other thing is to double and triple check all earths around the engine. Link has a good feature to tell you when inputs are off scale and erroring too. It's all in the help menu. 1 Link to comment https://www.sau.com.au/forums/topic/479735-gt-t-link-g4-first-start-failed/#findComment-7924596 Share on other sites More sharing options...
Kinkstaah Posted February 10, 2020 Share Posted February 10, 2020 Above post is good, but just to confirm, actually confirm that you have fuel, air, spark. Just because the ECU is attempting to fire the injector doesn't always mean the injector is being fired. As above, you may need to see what IAT is used when the sensor is unplugged, it will have a fail condition. The link forum may be of more help here. At this point (and the joys of standalone ecus) your link could be running any engine. 1 Link to comment https://www.sau.com.au/forums/topic/479735-gt-t-link-g4-first-start-failed/#findComment-7924604 Share on other sites More sharing options...
Finn_GT-T Posted February 11, 2020 Author Share Posted February 11, 2020 (edited) I've done some checks yesterday. Spark test was successfull but the spark plug seem to stay dry. Fuelpump is working and there is fuel in the fuelrail and pressure on the fuellines. So I think the injectors are not getting fired in the correct way. Deatschwerks say that they are p&p for the gt-t, I'll check if that information is correct. Does anyone have more information about that? I used 21S-05-0600-6. When I disable the iat in PcLink the ecu sets a permanent temperature of 21°C. Edited February 11, 2020 by Finn_GT-T Link to comment https://www.sau.com.au/forums/topic/479735-gt-t-link-g4-first-start-failed/#findComment-7924644 Share on other sites More sharing options...
KiwiRS4T Posted February 12, 2020 Share Posted February 12, 2020 Ref the Link forum or ring or email Link directly. Link to comment https://www.sau.com.au/forums/topic/479735-gt-t-link-g4-first-start-failed/#findComment-7924716 Share on other sites More sharing options...
robbo_rb180 Posted February 12, 2020 Share Posted February 12, 2020 As has been said the Link help file has all information needed to get it running. Need to set trigger widest slot and trigger offset values. Depending on what fuel mode you use will depend on how you tune it. Next is injector data THIS IS IMPORTANT especially with modelled fuel. The base file is helpful but generally doesn't get it running if you have never used one or have a good understanding of how the ecu works. You need a Wideband sensor and controller to tune, wire to a AN input or to CAN. Factory narrow band is useless. IAT is only used for corrections but is definitely a must. May pay to get a workshop or someone who knows what they are doing to get it sorted. Or if you need more info PM me. Link to comment https://www.sau.com.au/forums/topic/479735-gt-t-link-g4-first-start-failed/#findComment-7924726 Share on other sites More sharing options...
Finn_GT-T Posted February 12, 2020 Author Share Posted February 12, 2020 (edited) Ok mates, finally I solved the riddle with the help of the injector testing function. The solution was just as simple as plugging in the connector of the injector harness...lol Now the engine is running...not very well, but i runs. Thank's for your help! So here's my next question for you: Deatschwerks provides the following data sheet: https://www.deatschwerks.com/sites/www.deatschwerks.com/files/DATA/injectordata/21S-XX-0600-XX%20Injector%20Characterization%20Summary.pdf I already adjusted the dead time table in PcLink. But where do i put the values from the "Pulsed Flow Data"-table of the data sheet? Is that the right data for the "injector short pulse width adder table"? Edited February 12, 2020 by Finn_GT-T Link to comment https://www.sau.com.au/forums/topic/479735-gt-t-link-g4-first-start-failed/#findComment-7924729 Share on other sites More sharing options...
GTSBoy Posted February 12, 2020 Share Posted February 12, 2020 Sort of. You'll see that below 2ms the section of table is labelled "non-linear". That means you need to look at how far off the linear line the flows are there, and add some small % to the ECU's output, to compensate. Link to comment https://www.sau.com.au/forums/topic/479735-gt-t-link-g4-first-start-failed/#findComment-7924734 Share on other sites More sharing options...
Finn_GT-T Posted February 13, 2020 Author Share Posted February 13, 2020 Ok, if I unterstood you correctly: It is not necessary to insert the whole flow dataset somewhere in PcLink, but only the correction to get a linear line below 2.2 ms? Link to comment https://www.sau.com.au/forums/topic/479735-gt-t-link-g4-first-start-failed/#findComment-7924764 Share on other sites More sharing options...
GTSBoy Posted February 13, 2020 Share Posted February 13, 2020 I don't know how it is done in Link. You might have a single percentage adjustment number to put in, or there might be several points you need to fill. Whatever it is, you are looking to bump up whatever the ECU thinks it should do for a pulsewidth by a small amount at low pulsewidths to account for the fact that injectors don't flow as well as they "should" at low pulsewidths. Link to comment https://www.sau.com.au/forums/topic/479735-gt-t-link-g4-first-start-failed/#findComment-7924769 Share on other sites More sharing options...
Finn_GT-T Posted February 14, 2020 Author Share Posted February 14, 2020 Ok, then the adder table should be the right one for that. Thank you! Link to comment https://www.sau.com.au/forums/topic/479735-gt-t-link-g4-first-start-failed/#findComment-7924819 Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now