Jump to content
SAU Community

Recommended Posts

Don't worry about the shifting guide. You can change up at any speed between idle and redline. The only question after that is whether it will have enough torque to swallow much throttle opening in the next gear> RB20s have little torque, so the answer to that question will be "no" unless you're above about 3k rpm. And just to the right of the speedo is the gauge that will tell you about that.

The km to mile conversions are correct enough. Everyone since forever has treated the conversion as 40=60, 50=80, 60=100 and 70=110, to within the accuracy that matters.

For efficiency shift based on the peak efficiency RPM, shift just past the peak efficiency point while maximizing load without encountering high load enrichment so you sweep through the efficiency sweet spot. Looking at the gearing of the GTRs it looks like you want to be shifting at 3000 RPM so you drop down to ~2000 RPM when accelerating. Hold the engine right around 50-60% throttle if this is an NA engine or right at atmospheric pressure for turbo engines for best results.

For cruising pick the highest gear that doesn't have you exceeding the accelerating throttle condition. As for the best speed to cruise at, something high enough that you aren't running below 2000 RPM and something low enough that you don't exceed 3000 RPM.

  • Like 1
3 minutes ago, joshuaho96 said:

It's simple, it's the condition where you are accelerating with the throttle.

How do you accelerate without using the throttle... unless rolling down a hill? ?

3 minutes ago, Piggaz said:

How do you accelerate without using the throttle... unless rolling down a hill? ?

Very carefully?

Jokes aside the point is that lugging the engine at 1500 RPM and WOT to cruise is going to actually be quite inefficient even if the pumping loss is minimized. It's better to cruise at 2500 RPM with less throttle. The exact numbers are going to vary by engine but the principle is the same.

1 hour ago, joshuaho96 said:

Very carefully?

Jokes aside the point is that lugging the engine at 1500 RPM and WOT to cruise is going to actually be quite inefficient even if the pumping loss is minimized. It's better to cruise at 2500 RPM with less throttle. The exact numbers are going to vary by engine but the principle is the same.

Can you explain how you came to this conclusion? 

I am interested in the math and any other data you are relying on to make this statement. 

  • Haha 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeah. air pressure leakdown test is where I would be headed next here, using one's ears to determine whether it's the valves or bores/rings leaking...
    • More likely you didn't bed the rings in correctly and have glazed the bores. Running with misfires on a fresh build is somewhat of a no-no. Surely no-one "smoke tests" the combustion chamber? That's what a leakdown test is for. Smoke testing is, um, a bit of a wank at best, and only really useful for external pipework.  
    • Well, obviously that kit is not a relocation kit or anything other than just the original isolators and the like. I would suggest that it should be a matter of just bending up some flat bar to build a mount over the top of some other diff, with the flat bar held to the back of the diff by the rear hat bolts. A little welding, a little thinking about how to secure the front of this structure, maybe some different hoses in case you can't get it in just the right place.
    • Pay diff/trans workshop to do this.   Nope. Z32 turbo ran R230 with 6 bolt GTR style axles. All other Z32 were R200. Basically same same as other R32 stuff. All were a viscous waste of space.
    • So, I'm not a diff swapsies specialist, but I am pretty sure the 300zx ran an R220 not and R200 like the C34 Stagea, so I think it is of no use to you. As you said, all you need to do is get the centre swapped in the diff you have, which might be best done by a diff specialist. The current centre is probably desirable to someone to track so an easy path might be to swap your mechanical centre for someone with a standard centre (which is a viscous LSD, and almost certainly won't have any limited left). The only thing you have to watch swapping R200 internals between diffs is that the number of splines on your car's stub axles has to match the donor car, or you need the centre+stub axles and make sure they have the same number and pattern of bolt holes as your rear axles.  You swap your current ratio onto the new centre so you don't have to worry about matching the front. Alternatively, centres like the Nismo pro are much gentler (and have adjustable "tightness") so you could buy on of those from somewhere like Jesse Streeter or Nengun (noting it may cost you 1234% extra in tariffs by the time it lands)
×
×
  • Create New...