Jump to content
SAU Community

Recommended Posts

On 23/03/2020 at 3:45 PM, GTSBoy said:

I have decided to not participate in this discussion any further. Please consider this an act of social distancing, to prevent the risk of infection.

You are now infected....

Shit, now I am too. ?

4 minutes ago, GTSBoy said:

Except aero drag is already becoming dominant at that speed and you will almost certainly do better at 90 km/h than 120.

That is true, 90 kph is generally going to yield better mpg than 120 even if the BSFC is worse. But most highways in my area will have everyone doing 100+ kph, late at night 130 kph is not unusual. May as well go a little faster and not risk getting rear-ended. Only on certain arterial roads is it possible to safely do 75-90 kph in my area.

  • 3 weeks later...
On 3/20/2020 at 9:09 PM, joshuaho96 said:

For efficiency shift based on the peak efficiency RPM, shift just past the peak efficiency point while maximizing load without encountering high load enrichment so you sweep through the efficiency sweet spot. Looking at the gearing of the GTRs it looks like you want to be shifting at 3000 RPM so you drop down to ~2000 RPM when accelerating. Hold the engine right around 50-60% throttle if this is an NA engine or right at atmospheric pressure for turbo engines for best results.

For cruising pick the highest gear that doesn't have you exceeding the accelerating throttle condition. As for the best speed to cruise at, something high enough that you aren't running below 2000 RPM and something low enough that you don't exceed 3000 RPM.

thank you for replying respectfully. I'm just getting into cars. I have wanted this car specifically for a long time. I've never driven a manual vehicle but I hear it isn't insanely difficult. I'm trying to drive this car as a daily. (yes I know it's not ideal but IDC) I just want to know the best way to driving this car efficiently while also having some fun here and there.

On 3/19/2020 at 11:24 PM, Anonymous said:

So I've made a little picture that kinda explains what gear to be in and converts the Km to mph on the speedo of a skyline. Does it look correct? Im using this as future reference. (If i manage to buy an r32)

Just get a Greddy Informeter and get their adapter harness for pre-OBD Nissan consult.  It plugs right into the consult port and gives you all the telemetries you need in unit you prefer, including MPH and coolant temp in 掳F.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Update: I got the magnet out. I bought 3 different flexible magnetic reach tools, but none of them worked. The magnet on the tip was all less than 2lbs of force, so i had to buy a special cylindrical magnet that had a pull force of 9lbs.  The magnet finally came in the mail yesterday, so i got under the car to get to work. The super strong magnet isn't that long, so i only have about 1 finger pinch lengths to hold it. I was so scared when i was going in the hole, that the 9lb magnet would just fly away inside the oil pan never to be seen again, but i had my butt cheeks clenched and finger gripped on that thing so tight, i managed to get it to suck the other magnet out.  It was a victory for me last night.         
    • Yep, pretty much what you said is a good summary. The aftermarket thing just attached to the rim, then has two lines out to valve stems, one to inner wheel, one to outer wheel. Some of the systems even start to air up as you head towards highway speed. IE, you're in the logging tracks, then as speeds increase it knows you're on tarmac and airs up so the driver doesn't even have to remember. I bet the ones that need driver intervention to air up end up seeing a lot more tyre wear from "forest pressures" in use on the highway!
    • Yes, but you need to do these type certifications for tuning parts. That is the absurd part here. Meaning tuning parts are very costly (generally speaking) as well as the technical test documentation for say a turbo swap with more power. It just makes modifying everything crazy expensive and complicated. That bracket has been lost in translation many years ago I assume, it was not there.
    • Hahaha, yeah.... not what you'd call a tamper-proof design.... but yes, with the truck setup, the lines are always connected, but typically they sit just inside the plane of the rear metal mudguards, so if you clear the guards you clear the lines as well. Not rogue 4WD tracks with tree branches and bushes everywhere, ready to hook-up an air hose. You can do it externally like a mod, but dedicated setups air-pressurize the undriven hubs, and on driven axles you can do the same thing, or pressurize the axles (lots of designs out there for this idea)... https://www.trtaustralia.com.au/traction-air-cti-system/  for example.... ..the trouble I've got here... wrt the bimmer ad... is the last bit...they don't want to show it spinning, do they.... give all the illusion that things are moving...but no...and what the hell tyre profile is that?...25??? ...far kernel, rims would be dead inside 10klms on most roads around here.... 馃槂
    • You're just describing how type certification works. Personally I would be shocked to discover that catalytic converter is not in the stock mounting position. Is there a bracket on the transfer case holding the catalytic converter and front pipe together? If so, it should be in stock position. 
  • Create New...