Jump to content
SAU Community

Recommended Posts

My reverse lights don’t work. There was only one fuse blown in the car and it was a/t control fuse what ever that is but I replaced it Incase it had something to do with it and they still don’t work.

i then checked the globes and they look fine, just a bit of rust in the plug the globe sits in. I then checked to see if power was getting to the connector in the boot and still nothing. So I believe it’s the reverse light switch, however I can’t find it. Is it on the side of the gearbox or is it built into the auto selector? Can anyone guide me in the right direction please.

thanks

1 hour ago, GTSBoy said:

a/t means Automatic Transmission. A good clue that something is f**ked down there. You don't blow fuses for no reason.

Have you tried searching for "reverse switch auto" on here?

Previous owner did a trans swap because it was bad so I’m assuming/hoping it blew from the old one. As for searching on here I can only find things relating to people doing auto to manual swaps and having trouble with wiring. All I really want is just to know where the location of the switch is so I can test it.

14 minutes ago, Rusty Nuts said:

If you had just followed the advice that GTSBoy had given you the fourth entry of the search gives you the answer.

The fourth one for me shows a guy wanting to connect the wires from an auto box look to a manual box. Is the plug in a different location on the automatic transmission and is the trans the same on the r33 as the r32? If that’s not the right one could you link me the one you are talking about?

  • 2 weeks later...

I still can’t find this stupid reverse switch. I did also find out it has 5 gears which makes it a Re5R01a, not sure if that makes a difference in the location or not but there is very limited info on this so I might just end up taking it to a professional seeing as how retarted I am

3 hours ago, GTSBoy said:

I would strongly suggest, that like most early automatics, the reverse switch is bundled up with the inhibitor switch in the shifter.

Like as in it’s inside the car? Not under or screwed in the side of the trans?

This is why my fuses kept blowing. I ended up putting a bigger fuse in and ran it until something started smoking, And well the dash is the last place I expected. I replaced the part as I was lucky enough to have a second one laying around. Everything works fine now.

FFC58F06-1982-4725-BDA8-A04CD5E43558.jpeg

5D1D11F2-0A21-436D-86DB-E1A1E45D3DB3.jpeg

Edited by Steem
3 hours ago, GTSBoy said:

As a diagnostic tool, despite it revealing your problem, I find it horrifying.

Yes I agree it’s not the best way but I have spent too long trying to fix this with little tools I have. It was a last resort. But I also want to thank you for your help with both problems I have posted here, I really appreciate it

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • In a few years from now, you'll regret that. It'll eat away at you, knowing the truth of the ugly hiding beneath the beautiful exterior... 😛
    • I don't think the G2 profile is particularly dangerous for the engine per se, more just are you actually ok with the turbo lag trade-offs? If the answer is yes then go for it. I personally don't think I'd be ok with it because I spend so much time at lower RPMs and I really enjoy the feeling of being able to stay in 5th gear on the highway and just roll into the throttle to get boost. Or staying in 3rd gear on "gentle canyon cruises" without feeling the turbo lag too badly. The 525 pump should be able to run flat out on factory lines but I would bet the pressure drop from pump to regulator is quite impressive. I don't know how much it would be exactly but I've seen figures like 30 psi thrown around.
    • It's interesting seeing everyone talk about what level of risk they are happy to tolerate.  Building a GTR always has a level of risk, you could be that lucky guy that drops 20k on the engine build alone and still has the thing go pop on the dyno. Life is fun like that.  The way I see it, the thing is a toy to be enjoyed. I'd be happy to turn up the power on stock motor and limit the risk with sensible tuning and engine protection. If it still goes pop, it is what it is. The car isn't a daily driver so it can happily sit while a plan is made to sort it out.  Given this thing will be a street car only, I really feel it's worth the (relatively small if managed well) risk to turn the power up to around 350KW on e85.  I don't think anyone getting into the skyline game now is doing it out of logic. Surely it is a purely emotional decision so I'm not sure how important it is to think about the engine build logically. The heart wants what it wants.  @joshuaho96 little note for Josh, I run my 525 pump flat out all the time and through the factory lines without any issues. (excluding the melting connectors, that's sorted now. we'll pretend it never happened lol)
    • But the Nexus S3 is very expensive and won't be as purpose-built for the application as a separate electronic boost controller :^) More seriously my pet issue here would be that the Walbro 525 running at 100% duty cycle is going to require more FPR than the stock setup can handle. I'm also pretty sure from what I've seen elsewhere you might want to slow down the pump regardless unless you're going to come up with some way of upsizing the fuel lines coming from the fuel tank. Factory 8mm fuel line doesn't actually flow very much if you want to keep pressure drop down between the fuel pump outlet and FPR. If you really want to "keep it simple" I would run only as much pump as you need and source a fuel pump controller to slow down the pump in the vain hope of being able to run stock-style FPRs which are pretty dinky. Or just use the HICAS lines and it should be mostly fine. OP should also really think hard about what profile they'd want out of the turbo. My pet choice here would be the G1 profile rather than anything higher power but YMMV. I already think ~stock turbo lag is pretty bad so I don't want to make it worse. In "gentle canyon cruising" I found that I spent a lot of time around 4-4.5k RPM. I also recommend DIYing labor if you're detail-oriented enough. Costs are high for labor + if you do it yourself you can be your own quality control.
    • GTSBoy is again on the money. My actual advice? Sell the car. (really). For what it's worth as is, you can sidegrade into something much better. If you care about function then this is the actual move. If you want a Skyline to perform, set aside about $100K to do it. This is NOT a typo. You will see right away these are two very different mindsets. Realistically we're talking full restomod for any Skyline still kicking around. Have an honest think about which one you are.. and what you want to do, and how much you want to invest in this (with no return).
×
×
  • Create New...