Jump to content
SAU Community

Recommended Posts

Hi all,

I'm trying to register my Stagea M35 in the ACT. It's currently registered in NSW.

Following the inspection there was a huge list of stuff I needed to fix, which has all been done.

One thing remains, the guys at the ACT Vehicle Inspection Station are not convinced that the three child restraint anchorage (CRA) points located on the inside of the roof, right at the back are compliant.

The fact that my vehicle was complied already in NSW and has the purple sticker doesn't sway them. They've asked me to provide the Consumer Information Notice (CIN) to prove that the CRA points are fitted where they're meant to be.

My purple sticker shows that my vehicle was complied by a company called Australian Compliance Centre Pty Ltd and when I search for them, I discover that they've ceased trading. So I have written to the RAWS section at the Department of Infrastructure asking if they can provide the CIN.

What a nightmare.

Does anyone have or know where I can find some documentation that proves the correct location of these CRA points?

Thanks,
Keir

Link to comment
https://www.sau.com.au/forums/topic/480039-compliance-help-needed/
Share on other sites

Ours came from QLD and I've been to Hume recently - wheels and brake upgrade (ATTKD 350Z front and 350Z rear) had to be engineered and all tint had to come off. That's been done and ready for retest. The child restraint points are mounted in the roof inside the back hatch - same place as in our ARX (which went through Hume when we bought it).  And they definitely checked them. 

I guess my point was that the inspector is mistaken and it might be useful to take it up with the superviser.  Anyway, I have the M35 Owner's Manual and if you PM me your mobile I'll SMS the page dealing with Child Anchorage Locations.  It might be helpful.

  • Like 1
On 28/03/2020 at 12:05 AM, karter said:

PM me your mobile I'll SMS the page dealing with Child Anchorage Locations.  It might be helpful.

Thanks so much for helping me out with this. I went back to the Hume Inspection Station this morning armed with the documentation and it actually swayed them. My Stagea now has ACT number plates!

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I would again like too thank Matt for his help in me sourcing the detachable hard top for the little red car, without Matt's assistance in inspecting it and locking it down, I can guarantee it would have sold before I could get up to see it,  and as that was the only available NC hardtop in Australia, I consider myself extremely lucky on multiple levels To say I'm more that happy would be an understatement And, it is 100% water tight, I drove through torrential rain coming back south, and by torrential, they type of rain that doing 40kph in a 110kph zone was a real thing, and even then, the standing water on the Hwy was deep enough to throw waves I'm also more than happy that the huge "BEASTS" that Matt calls dogs didn't eat me for lunch, I'm sure the sniffs and licks were more to "taste test" me, over being to friendly Now to work out what colour to get it painted, panel match, or gloss black........first world problems are real
    • Actually I might have figured out. Looks like there is a tab according to google images but it's hidden. Silly me.
    • No clips on this one like the other connector. Only that red tab that I can push slightly up.
    • For any loom connector that has an obvious release that resists pushing far enough to unclip, just spray some silicone lube into it. You might also benefit from using a bent screwdriver or small pick to push in the right place at the right angle.
    • Hey all, I went to try and fix my indicator not canceling, but I couldn't remove the clockspring cable under the column so I could twist that green thin. Anyone know how to remove this cable? I see this red tab but didn't have any luck. I was thinking of unscrewing it but wasn't sure if it would cause issues. I did notice for my indicator stalk, 2 out of 3 cables were plugged in but the last cable wouldn't fit in the stalk. I'm getting it's for fog lights. It was like this when I originally pulled it off.  
×
×
  • Create New...