Jump to content
SAU Community

Recommended Posts

so for some unknown reason I wanted to own a skyline as a daily once again and re-live my youth, I had a very tight budget and the cheapest turboed skylines around seemed to be R33 gts-t's, not really my favorite model but hopefully I can make something nice out of it..

the first R33 I bought was the cheapest one in the state at the time, I rushed into it and hardly looked at it and threw them the money and drove it 600kms home,  it had a lot of issues that needed to be fixed and had clearly seen some abuse in its time

once I got it home I put it up on stands straight away and started inspecting everything, upon inspection it was found that all of the VIN plates were missing...import plates, vin number grinded off the chassis, ignition barrel had also been swapped at some point, cracks in front control arms, blown out shocks all round, all bushed flogged out and chassis rail looked like an 80's hip hop song....M.C f**kin hammered.

I went to the police station had them inspect the car, run the rego papers that I had, check engine numbers etc, turned out that the car had been stolen previously and then recovered and returned to its owners who then sold it on to mentally disabled me...

they stated that the car would have to go to regency and be "re-plated" but they doubted that it would even be possible and the car may have to be taken off the road for good...

so I started searching for a rolling shell, there comes my next purchase, I found a clean shell that had been resprayed, not the greatest paint job but much better condition of a shell then my current car and plus it was all legit, which isn't completely necessary..."BUT IT HELPS"

so here is the real start of my journey, I had one week to swap everything from one car to another, get it all running and fix every dam issue with it. otherwise I would not have a car to be able to drive to work.

Switcherooo time

 

Link to comment
https://www.sau.com.au/forums/topic/480283-r33-daily-work-hack/
Share on other sites

so for some unknown reason I wanted to own a skyline as a daily once again and re-live my youth, I had a very tight budget and the cheapest turboed skylines around seemed to be R33 gts-t's, not really my favorite model but hopefully I can make something nice out of it..

the first R33 I bought was the cheapest one in the state at the time, I rushed into it and hardly looked at it and threw them the money and drove it 600kms home,  it had a lot of issues that needed to be fixed and had clearly seen some abuse in its time

 

once I got it home I put it up on stands straight away and started inspecting everything, upon inspection it was found that all of the VIN plates were missing...import plates, vin number grinded off the chassis, ignition barrel had also been swapped at some point, cracks in front control arms, blown out shocks all round, all bushed flogged out and chassis rail looked like an 80's hip hop song....M.C f**kin hammered.

I went to the police station had them inspect the car, run the rego papers that I had, check engine numbers etc, turned out that the car had been stolen previously and then recovered and returned to its owners who then sold it on to mentally disabled me...

they stated that the car would have to go to regency and be "re-plated" but they doubted that it would even be possible and the car may have to be taken off the road for good...

IMG_0264.JPG

  • Haha 1

so I started searching for a rolling shell, there comes my next purchase, I found a clean shell that had been resprayed, not the greatest paint job but much better condition of a shell then my current car and plus it was all legit, which isn't completely necessary..."BUT IT HELPS"

IMG_0398.PNG

IMG_0484.JPG

so here is the real start of my journey, I had one week to swap everything from one car to another, get it all running and fix every dam issue with it. otherwise I would not have a car to be able to drive to work.

IMG_0485.JPG

IMG_0487.JPG

IMG_0488.JPG

IMG_0489.JPG

IMG_0490.JPG

IMG_0491.JPG

IMG_0492.JPG

IMG_0493.JPG

IMG_0496.JPG

IMG_0497.JPG

IMG_0498.JPG

IMG_0499.JPG

IMG_0505.JPG

IMG_0510.JPG

IMG_0515.JPG

Switcherooo time

this involved swapping everything from the white car to the red, heater core, dash assembly, air con, engine loom, engine and trans, rear cradle and diff, replaced all bushes (except rear cradle and front upper outer control arm bushes) replaced tie rods, and timing belt for good measure, it was a busy 5 days too say the least

car has also acquired some gtr seats, old as hell tein rear coilovers, 3" exhaust, hi flow cat annnnd adjustable castor rods

IMG_0511.JPG

IMG_0525.JPG

IMG_0527.JPG

IMG_0530.JPG

IMG_0531.JPG

IMG_0535.JPG

IMG_0536.JPG

IMG_0543.JPG

IMG_0544.JPG

IMG_0548.JPG

IMG_0553.JPG

IMG_0559.JPG

IMG_0563.JPG

IMG_0565.JPG

IMG_0567.JPG

IMG_0587.JPG

IMG_0589.JPG

IMG_0592.JPG

IMG_0595.JPG

IMG_0596.JPG

IMG_0776.JPG

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yes to both! Yes to standard ECU and tune, but exhaust is aftermarket. Unsure on brand. Actually have it sitting in at my desk haha! I have to set it up on my laptop but this is a great next step, will do. So I generally try to shift before 4.5K RPM most times. I largely don't do a lot of high-rev driving, but I will take it up to red 1-2x a week max, as I know the occasional "Italian tune-up" is good for these cars.  Oh wow, is this way better than what I'm getting. Does this mean there's a good chance I have an issue?   Thanks for all the info so far guys.
    • Old Son, did you re-use the Holden ABS in the new shell or try a different module?
    • Yeah, nah. I had the actuator rod off it today. The arm will not move at all. Neither out, nor in. Yeah, you'd think so, but I've been thinking about that. Even when the actuator rod fell all the way off at the beginning of this saga, it would build more boost and faster in lower gears than it would in higher gears, and you'd think that that was the opposite of what should happen. But I strongly suspect that there is a thing with the gearing getting the revs to rise faster, that there must be some transient effect with the gas flow rate rising quickly, that you don't get with the more steady state case of the higher gears. Keep in mind - the gate is not shut in either of my weirdnesses. So things are not "normal". We normally think about a turbo spooling up (below the wastegate target) with the gate shut. I have all sorts of mental models running now where the gate is a little bit open, and having it stuck open allowing gas out while it should be going through the turbine has all sorts of weird effects (in these mental models). I'm thinking in the higher gears, the ex mani pressure builds to the point where enough gases spill out the wastegate to just prevent the pressure rising much more at all, or just creeping up, all the whole the revs are increasing and getting closer to the point where a gear shift becomes necessary.
    • Is it possibly wastegate actuator itself is sticking, or even the rod to flapper? Otherwise I reckon things are getting a bit rusty/worn   Also odd it won't boost in 3rd to 5th, but will in 1st, I'd expect the other way around with it slightly open as there's more time on your way to redline for it to spin up
    • Does anyone know ow what these two plugs are for and if they should be unplugged? Just put the dash back together and can't remember if these were plugged in before or unplugged! (Blue and white plugs) 🤦🏽‍♂️
×
×
  • Create New...